The uniform thin pin-connected bars AB, BC, and CD have masses mAB= 2.3 kg, mBC= 3.2 kg, and mCD= 5.0 kg, respectively. Letting R = 0.75 m, L = 1.2 m, and H= 1.55 m and knowing that bar AB rotates at a constant angular velocity WAB= 4 rad/s, compute the angular momentum of bar AB about A, of bar BC about A, and bar CD about D at the instant shown. R B WAB + H The angular momentum of bar AB about A is The angular momentum of bar BC about A is ( The angular momentum of bar CD about Dis ( kg-m²/s) k. |kg-m²/s) k. kg.m²/s) k.

The uniform thin pin-connected bars AB, BC, and CD have masses mAB= 2.3 kg, mBC= 3.2 kg, and mCD= 5.0 kg, respectively. Letting R = 0.75 m, L = 1.2 m, and H= 1.55 m and knowing that bar AB rotates at a constant angular velocity WAB= 4 rad/s, compute the angular momentum of bar AB about A, of bar BC about A, and bar CD about D at the instant shown. R B WAB + H The angular momentum of bar AB about A is The angular momentum of bar BC about A is ( The angular momentum of bar CD about Dis ( kg-m²/s) k. |kg-m²/s) k. kg.m²/s) k.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Dynamics Lesson:I want detailed and manual solution.
A homogeneous disk of mass m = 4 kg rotates at the constant rate wi = 12 rad/s with respect to arm OA, which itself rotates at the constant rate wz = 4 rad/s about the y- axis, determine: 1. Angular momentum of the disk about point A. 2. Angular momentum of the disk about point O. 3. The force-couple system representing the dynamic reactions at the support. Neglect the mass of of arm OA. 320 min 200 mm T = 100 mm
3. Express the kinetic energy of each of the systems and determine the number of degrees of freedom of each system in terms of the specified generalized coordinates. Slender bar of mass m Slender bar of mass m To (a) (c)
Blocks A and B shown in the figure have masses of 5 kg and 10 kg respectively.If the pulley is treated as a 3 kg solid disk with a 15 cm radius, determine the acceleration of the block A. Disregard the rope mass and any slip on the pulley.Consider that the moment of inertia of the pulley is given by Ip = (1/2)mr² in which m is the mass of the pulley and r is of radius the pulley.
A cylinder of mass m, radius r and radius of gyration k is released from rest and rolls without slipping down a plane inclined at an angle a to the horizontal. Use the conservation of energy or an alternative method to derive an expression for the acceleration of the cylinder down the slope due to gravity.
In an under-construction building, an elevator lift has to be installed to ease the movement of engineers, workers, etc. from the ground floor to the top floor. The elevator lift is of mass 2.95 tons including passengers (workers and engineers) and has to be raised with an acceleration of 55 m/s using a hoist drum of 1.9 m diameter. The drum's mass is 810 kg and the radius of gyration is 465 mm. The effect of bearing friction is equivalent to a couple of 2.8 kN-m at the host drum. A motor has to be selected based on torque requirement and you (working as an Engineer at a construction site) have been asked by your supervisor to carry out the following tasks. Determine the Value of Moment of Inertia I kg-m2 Determine the Value of Effort in the rope to lift the elevator E= N-m Determine the Value of Torque T=
A 10 kg disc is acted upon an external force and a couple as found in the figure. The Disc was initially at rest. Assume that the mass moment of inertia of the disc is 0.25 kg.m² R = 0.5 m Horizontal Reaction force at O after 2 seconds. (N) Determine the angular velocity of the disc after 2 seconds (rad/s) (CW) Vertical Reaction force at O after 2 seconds. (N) M = 20 N.m F = 200 N Choose... Choose... # Choose O
Derive the equations of motion using Lagrange's equations. (I, =mr? ) THE MOTION IS ON THE HORIZONTAL PLANE (NO GRAVITY) Trailer, mass M Cylinder, k1 mass m k2
4 -(Kinetics of Curvilinear Motion) Tow weights W, and W2 of 8KN and 5KN are attached at the ends of a flexible cable. The cable passes over a pulley of 100 cm diameter. The weight of the pulley is 600N with a radius of gyration of 50cm about its axis of rotation. Find the torque which must be applied to the pulley to raise the 8KN weight with an acceleration 1.5 m/s?. Neglect friction in the pulley bearing. 50 cm 600N T 8kN 5kN W,
P.3) Determine the angular momentum Hp for the three masses A, B, and C (ma = mB = mc 0.2 kg) when all three masses are clustered at the origin O of the Cartesian coordinate axes. The point P is located at 0.1 m away from the origin in k direction. The velocities of the masses are; VA = 0.05 i m/s, vB = 0.05 į m/s, and vc = 0.05 k m/s. CB P
3.32). As shown in Figure 3, a yo-yo toy is formed by wrapping a massless cord around adisk of radius R= 0.2 m and mass M=3 kg. The cord is vertical and its top end is fixed and the disk isinitially stationary. The cord remains vertical for the entire motion and does not slide on the disk.When the disk is released from rest, it falls down by a distance H=0.8 m, The moment of inertia ofthe disk around its center is I disk=1/2mdiskR^2a . Find the angular acceleration of the disk when it is lowered by a distance H.b . Find the angular velocity of the disk when it is lowered by a distance H.
A homogeneous rad of mass M = 11 kg and length L = 12 m spins around its center of mass with an angular speed w = 12 radian/s on a horizontal frictionless surface of a table. The location of the center of mass of the rod on the table is stationary although the center of mass is not pivoted to the table. As the rod spins, a point-like particle of mass m = 2 kg is placed at rest on the table as shown in the figure and the end of the rod collides elastically with it. After the collision, the rod has only a translational motion, and no rotational motion. What is the speed v of the rod, in units of m/s, after the collision? (Suggestion: You may use conservation of linear momentum and conservation of angular momentum (about the fixed point on the table where the center of mass of the rod was initially spinning on.) (The moment of inertia of the rod about the axis through the center of mass I = 1 ML?) O 24.00 6.00 O 30.00 O 12.00 O 36.00