‘The uniform brass bar AB has a rectangular cross section and is supported by pins and brackets as shown. Each end of the bar can rotate freely about a horizontal axis through the pin, but rotation about a vertical axis is prevented by the brackets. (a) Determine the ratio b/d for which the factor of safety is the same about the horizontal and vertical axes. (b) Determine the factor of safety if P =1.8 kips , L= 7 ft. d =1.5in. and E= 20 X 10 psi The uniform brass bar AB has a rectangular cross section and is supported by pins and brackets as shown. Each end of the bar can rotate freely about ahorizontal axis through the pin, but rotation about a vertical axis is prevented by the brackets. (a) Determine the ratio b/d for which the factor of safety is thesame about the horizontal and vertical axes. (b) Determine the factor of safety if P = 1.8 kips, L= 7 ft, d = 1.5 in., and E = 29 X 106 psi.B

The maximum load is given by; .....…… (1) Where, - maximum in the horizontal side E -modulus…

The uniform brass bar AB has a rectangular cross section and is supported by pins and brackets as shown. Each end of the bar can rotate freely about a horizontal axis through the pin, but rotation about a vertical axis is prevented by the brackets. (a) Determine the ratio b/d for which the factor of safety is the same about the horizontal and vertical axes. (b) Determine the factor of safety if P =1.8 kips , L= 7 ft. d =1.5in. and E= 20 X 10

The uniform brass bar AB has a rectangular cross section and is supported by pins and brackets as shown. Each end of the bar can rotate freely about a horizontal axis through the pin, but rotation about a vertical axis is prevented by the brackets. (a) Determine the ratio b/d for which the factor of safety is the same about the horizontal and vertical axes. (b) Determine the factor of safety if P =1.8 kips , L= 7 ft. d =1.5in. and E= 20 X 10

Related questions

Q: Consider a rigid steel beam of length L = 13 m and mass mb = 383 kg resting on two supports, one at…

A: The beam is uniform and hence its center of mass lies equidistant from ends A and B. The worker…

Q: A uniform rod is attached to a wall by a hinge at its base. The rod has a mass of 7.5 kg, a length…

A: The mass of the rod is The length of the rod is The angle of the rod with the horizontal is

Q: 1. A 500 N weight from the end of a uniform strut the strut is 4 meters long and weighs 700N. The…

Q: One end of a uniform = 4.10-m-long rod of weight w is supported by a cable at an angle of 8 = 37°…

Q: If, in Fig. 9-4 and in Problem 9.33, h 2.5R, how large a force will the 50-g bead exert on the wire…

Q: A brake is applied to the rim of a wheel with a force of 2.50 kN and the coefficient of friction…

A: Given: The applied force on th rim is 2.5 kN. The coefficient of the friction is 0.4.

Q: ever system in static equilibrium has a 300 N resistive force and a 90 N motive or applied force…

A: Let the length between fulcrum and resistance is L resistance is paced at L . and 90 N is at 1.5…

Q: A uniform bar AB, 9 ft long, and weighing 5.0 lb, is supported by a fulcrum at point O as shown. If…

A: Given, Length of the bar=9 ft mass m=5 lb mA=12 lb rA=3 ft rB=6 ft

Q: Determine the magnitude of force at the pin A and in the cable BC needed to support the 500 N load.…

Q: The 30-N uniform rod has a length of l = 2 m. If s = 3 m, determine the distance h of placement at…

A: Given values:S = 3 mI = 2 m

Q: What general statement can be made about the units of the quantities used to calculate strain in a…

A: A strain is defined as the amount of change per unit length of a wire when a load is applied. A…

Q: Q.4) The tensile force in cable AB has a magnitude of 80 lb. The cable is attached to a collar at A…

Q: Using an allowable shearing stress of 3 ksi, design a solid steel shaft to transmit 17 hp at a speed…

Q: A 10 m long and 20 kg ladder leaned against a vertical wall at an angle of 53o to the horizontal.…

A: Consider the following figure which represents the direction of all the forces acting on the ladder.…

Q: Determine the force in each member of the loaded truss. The force is positive if in tension,…

A: The free-body diagram of the system is shown below.

Q: uniform beam of length ? and mass ? is inclined at an angle ? to the horizontal. Its

Q: 4-106. Replace the force system acting on the bracket by a resultant force and couple moment at…

A: Given data- let force F1=450 N, and force F2=600 N first we make free body diagram of force system-

Q: Determine the magnitude of the pin force at A. Assume W-640 lb, a-5.5 ft, b=3.9 ft, r = 8 in. W C a…

A: In this question , assume w-640 lb, a=5.5 ft. b=3.9 ft,r=8 in.determine the magnitude of the pin…

Question

‘The uniform brass bar AB has a rectangular cross section and is supported by pins and brackets as shown. Each end of the bar can rotate freely about a horizontal axis through the pin, but rotation about a vertical axis is prevented by the brackets. (a) Determine the ratio b/d for which the factor of safety is the same about the horizontal and vertical axes. (b) Determine the factor of safety if P =1.8 kips , L= 7 ft. d =1.5in. and E= 20 X 10 psi

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Trending now

This is a popular solution!

Step by step

Solved in 5 steps with 26 images

SEE SOLUTION Check out a sample Q&A here

Similar questions

for the below figure, the rod of mass 50kg and length 6m is in the equilibrium. It is hinged to a wall at 0. The rod is at an angle of 40˚ above the horizontal and the rope makes an angle of 70˚ with the rod. (a)find the tension in the rope (b)find the force exerted by the hinge 0 on the rod.
The uniform 19.0 kg beam below is 6.4 m long and is perfectly balanced about a point 1.4 m from the left end. What is the mass of the block? (Hint: when calculating the torque due to the weight of the beam, consider all of its mass to be located at its center of mass.)
.
5
ect loca tecd What would happen to the stick? the Figure A 10m long uniform bar with a 80 W is attac hed by africtionless hinge to weighte of horizontal rope that wall and held by a malces anr le Qof 37° witn the bar. Culculate the distance from the hinge, x, tha t the 10kg tension T in the rope is 25N. Hint: Use g 10 W/kg, sin37°360 and cos 37°: 9. ang should besus peded if the n fo?
Can you use a slanted rope attached from the wall to the end of the beam if that rope breaks when the tension exceeds 170 N? The beam is light.
Gold, which has a density of 19.32 g/cm3, is the most ductile metal and can be pressed into a thin leaf or drawn out into a long fiber. (b) If, instead, the gold is drawn out into a cylindrical fiber of radius 2.100 μm, what is the length of the fiber?
By finding the curl, determine which of the following forces are conservative: (a) F = ix +jy + kz (b) F = iy - jx + kz* (c) F = iy + jx + kz' 4.2 _3