The uniform beam is supported at its ends by two springs A and B, each having the same stiffness k. When nothing is supported on the beam, it has a period of vertical vibration of 0.83 s. If a 50-kg mass is placed at its center, the period of vertical vibration is 1.52 s. Compute the stiffness of each spring and the mass of the beam.

Q: What is the low limit on the smallest outside diameter?

A: Solution:

Q: 18. How far off from the center of the support is the center of the two holes in the bosses of the…

A: 18)    Distance=4.2-0.66                   =3.54 in

Q: From among the following select the truest statement. The Distortion Energy theory is a special case…

A: The given problem is based on theory of failure.

Q: Choose one of the following statements which is not true.

A: for solution refer below images.

Q: Q3: Mark the Following True or False 1. Hidden lines are used in sectioned area when they are needed…

A: 1.TRUE 2. TRUE 3.TRUE 4.FALSE 5. FALSE 6.FALSE 7.TRUE 8.FALSE 9.FALSE 10.FALSE 11.TRUE 12.TRUE…

Q: Sorry that's the wrong answer it is 0.62

A: Power coefficient = Cp=0.24 Wind speed = Vw=10.3 m/s Blade length = R = 34 m The power generated by…

Q: I need question 7 answered pertaining to the print provided. I asked this question previously on…

A: 7. According to ASME, the revision can be made either by making the changes in the revision block or…

Q: I need these 2 parts answered pertaining to the print provided. If you can not answer all 2 parts,…

A: AP-001The diameter of the hole that is inclined 15 is ϕ0.25. It can be viewed in the section A…

Q: R L2 (Side view) (End view)

A: Given data: α (Bend angle) =70° Kba (Strecth factor) =0.33  t  (Stock thickness) = 0.3" R (Width…

Q: 1.00 1.38 3.38 38 2.00

A: Select the correct statement about the notation circled in green and marked as letter D. Assume all…

Q: Write TRUE is the statement/s is True. If the statement is false, identify the word/s that makes the…

A: The chip compression ratio can be defined as the ratio of the chip thickness and uncut chip…

Q: At the instant the hand has stopped pushing, the tangential acceleration of the ruler is Group of…

A: Let the torque applied by hands be And the length of the ruler be The tangential acceleration can be…

Q: what happened with the 10 in the first equation?

A:

Q: What's the answer C onwards with working and correct answer and can you label it please as I have…

A: The ideal diesel cycle does not occur in practical life because the losses are not eliminated in…

Q: what is the bottom length?

A: To calculate the bottom length

Q: se explain how you got the P1 and P2 final numbers from the giv

A: We have given in question T=200 and 250 degrees Celsius P=17.3 and 74.4 mm of Hg

Q: C) What is the maximum possible mass flow rate that the pump can produce?

A:

Q: There are two samples, A and B, ere tested by Rockwell hardness test. Sample A is tested in B scale,…

A: HRB means the Hardness Rockwell B scale HRB means the Hardness Rockwell F scale

Q: I need answers for problems 7, 8, and 9 pertaining to the print provided.

A: As we are entitled to answer only a single question. We’ll answer question no. 7 for you. Please…

Q: Quenching is a process that can reduce the grain size and form a lot of grain boundaries in the…

A: Quenching: In this process metal is heated above its recrystallization and than cool it rapidly. The…

Q: This was not correct may you please

A:

Q: This answer was marked incorrect

A: The power input to the pump is 0.454 kW.

Q: 6 Using the drawing callout shown in Figure 5 below, which part(s) shown in Figure 4 would now…

A: According to the given dimensional tolerance for the part, the maximum and minimum allowable…

Q: Problem 2) As a result of loading, the rectangle with a = 25 mm and b = 18 mm deforms into a paral-…

A:

Q: the various parts? 13. What is the tolerance on "F," the chamfer angle? 13 14. How square must the…

A: 13. 6 ° is the tolerance on "F" the chamfer angle As 20° - 14° = 6°    14. square must the ends of…

Numerical Calculations

In the mid-20th century, the availability and the growth in power of digital computers led to the increase in the mathematical model in the field of engineering and science. The analysis of these detailed models needs to be increased.