Answered: the ultimate load capacity Wu of the…

Engineering

Civil Engineering

the ultimate load capacity Wu of the beam in KN/m considering flexure. Express your answer in 3 decimal places

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: PROBLEM 1] The cantilever beam shown below has the cross-section on the right portion. If the…

Q: The members of the truss are 25mmx50mm in cross section. Determine the maximum load P that can be…

A: Given:- The cross-section of the truss = 25 mm × 50 mm The maximum stress in tension = 100 MPa The…

Q: A 1016 mm P 25 mm 330 mm 25 mm 254 mm A 12.5 mm

A: Lets Draw SFD and BMD in terms of P value M=-P×1.016 kNmV=P kN

Q: 3) The simply supported beam with the cross-section as shown supports a total uniformly distributed…

A: Allowable tension flexural stress = 35 MPa Allowable compression flexural stress = 150 MPa

Q: 4. Find the lightest S-shape for the beam shown if the working stress in bending is 175 MPa. What is…

A: The given figure of beam is shown below:

Q: ) For a simply supported singly reinforced concrete beam of width b and effective depth d show that…

A: Assuming x=depth of the neutral axis As per BS 8110: C=AC×0.45fcuAC: Area of…

Q: A wide flange A60 steel column has a length of 5.8meters and pinned ends. If Sx=857x103 mm3,…

A: The following are the given information. A=7243 mm2 Fy=414 MPa Sx=857×103 mm3 Sy=135×103 mm3 d=358…

Q: Note: Please show all of the free body diagrams used and also show the complete solution. The beam…

A: Deflection will be determined by the first mentioned method i.e. double integration.For other…

Q: pported by this beam if the allowable WO IIIT x B 를 -를- LC kN/m

Q: P2 Ans: 5000 For the cross sections shown in figure (a) and (b) compare the 0.005m 0.2m torsional…

A: Given data, Inner radius = 0.2 m Thickness = 0.005 m To find out the radio of Torsional rigidity.…

Q: The beam below has a fixed support at A and a roller support at B. It is subject to transverse…

Q: Determine the allowable design axial load on a size 350mm x 350mm square column. The column has an…

Q: 3.4 Check the threshold validity below according to the bending requirement if 35MPa=m, f = 300 MPa.…

A: Dead load, DL = 5 kN/mLive Load, LL = 10 kN/mPL = 20 kNSpan, L = 4 mfc = 35 MPafy = 300 MPa3-25 mm…

Q: Rigid beam AB is supported by three bolts at A and a pin at B. The bolts at A are in double shear…

Q: lb concentrated forces were applied.

A: Reaction:RA=RB=30014+800+8002=2900lbMax shear = reaction =2900

Q: Determine the stress concentration factor for the beam shown below that has a fillet to the larger…

A: step 1-

Q: Axially Loaded Determine the allowable design axial load on a size 350 mm x 350 mm square column.…

A: Given data - Size = 350×350 mm L = 3.5 m E = 33.56 GPa Fc = 11.70 MPa Find out - The allowable…

Q: 1. The structure shown below is subjected to a total uniform load w. The flexural stress in the…

A: (a) Consider the free body diagram of beam; For CDE; Re×L+w(1)22+w(1)22=0Re=0 Calculate shear at…

Q: A concrete beam prestressed with a parabolic tendon is shown in the sketch. The eccentricity of the…

A: Given- Prestressing force=1620 kNUDL=45 kN/mcross section-width b=500 mmdepth d=750 mmIt is needed…

Q: What is the long-term deflection for dead load plus 45% permanent live load for 1 year, there is…

Q: Determine the maximum tension and compression stress for the aluminum double stem T section shown…

Q: Q1:If allowable stresses are o, 165MPa.0, 100MPa = 70MPa determine max. value of W. M 300mm Im 4m Im…

Q: 300 mm 200 mm T= 144N.m Cross sectional area of portion BC of the shaft d, = 50 mm d2 = 100 mm…

Q: A simply supported beam has a maximum moment equal to 20 KN.m. The beam has a width of 200 mm and a…

A: step 1-

Q: termine the

Q: A beam has a uniform dead load and live load has a fixed support at both ends. If the beam…

Q: The composite beam shown in the figure is simply supported and carries a total uniform load of 50…

Q: 3) The simply supported beam with the cross-section as shown supports a total uniformly distributed…

Q: 20 mm 20 mm A beam section shown is simply supported over a span of 4 m. Find the uniformly…

A: Given data : Section given is I section Length of beam (L)=4 m Bending stress (σ)=100 N/mm2 The beam…

Q: A 5-m long, simply supported beam is loaded as shown. Determine the lightest W-shape beam that can…

Q: Q1- A simply supported reinforced concrete beam has a cross-section as shown in the Figure 1.Using…

A: Pmax = 65 kN

Q: a) Is the beam properly reinforced/over-reinforced/ balanced Determine the factored moment…

A: RC Singly beam,b=500 mmD=700 mmd=600 mmf'c=48 MPaReinforcement: 3-30Mfy=400 MPaφc=0.65φs=0.85Es=2…

Q: The cantilever beam shown below has the cross-section on the right portion. If the allowable…

Q: In the truss shown below, ignore the zero-force members and formulate the stiffness matrix, load…

A: For a given truss, as per equilibrium conditions members AF, FG, GH and CH are zero force members.…

Q: AT beam supports the three concentrated loads shown in Fig. P-556. N.A. is 3.5 in., INA = 97.0 in.…

A: Given data: INA=97 in4

Q: 20 kN/m 20 kN 20 kN z (m) a 3 10

A: Given data Allowable stress = 300mPa b = 4a Free body diagram of given beam,

Q: A W21×101 is used as a compression member with one end fixed and the other end free. The length is…

A: Section-W21×101L=12 ftFy=50 ksi To find- Nominal compressive strength

Q: QUESTION: The distributed load on the T-section beam shown below and moment affects. A is the fixed…

Q: Question 6 The reinforced concrete beam shown in Figure 6 is encastré at both ends. It supports a…

A: Calculation of vertical reactions

Q: "Determine the minimum width "b" of the beam shown if the flexural stress is not to exceed 13 MPa.…

Q: 3) The simply supported beam with the cross-section as shown supports a total uniformly distributed…

Question

A 5.5m simple beam carries a uniform ultimate load Wu. The beam is laterally supported and has compact section. The properties of the section are: rx=105.16mm, ry=22.2mm, Sx=308000mm^3, Sy=35000mm^3, Zx=357000mm^3, Zy=55000mm^3, and Fy=248MPa. Calculate the ultimate load capacity Wu of the beam in KN/m considering flexure. Express your answer in 3 decimal places.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Similar questions

Question # 3: A cast iron beam is of 1-section as shown in Figure below. The beam is simply supported on a span of 5 metres. If the tensile stress is not to exceed 20 N/mm², find the safe uniformly load which the beam can carry. Find also the maximum compressive stress. 40 mm 20 mm 200 mm 80 mm 20 mm 160 mm. T
9. A steel portal frame has dimensions, plastic moment capacities and applied loads as shown in the figure. The vertical load is always twice of the horizontal load. The collapse load P required for the development of a beam mechanism is P A B Mp K 2P 2Mp L с Mp D L
3) The simply supported beam with the cross-section as shown supports a total uniformly distributed load of 4P and 2P and concentrated load P as shown in the figure. Determine the maximum allowable value of P if the allowable flexural stresses are limited to 35 MPa in tension and 150 MPa in compression respectively. 1m P B 1m IC 4P 3m D 2P 1m DE U 175 200 (Dimensions in mm)
The steel beam has the cross section shown. The beam length is L = 6.4 m, and the cross-sectional dimensions are d = 345 mm, by = 205 mm, t = 16 mm, and tw = 7 mm. Calculate the largest intensity of distributed load wo that can be supported by this beam if the allowable bending stress is 215 MPa. Answer: Wo Wo kN/m T₁₂ y
Current Attempt in Progress The cantilever beam consists of a rectangular structural steel tube shape [E = 29,000 ksi; = 1990 in."). For the loading shown, determine: (a) the beam deflection at point A. (b) the beam deflection at point B. Assume MA= 250 kip-ft, P= 14 kips, LAB = 4.1 ft, LBc = 6.2 ft. MA LAB LBC Answer: in. (a) VA- in. (b) VB - 4. Submi Attempts: 0 of 1 used Save for Later
A lightly welded steel beam shown in Figure 5 is continuously supported along its length. A downward concentrated load of 4P acts at Point C, and two downward concentrated loads P act at Points A and E. The beam with full lateral restraint is bent about its major principal x-axis. Determine the followings: a. Section type based on section slenderness; b. Effective section modulus; c. The maximum design value of P. A k B fu 6 m d tw bf 6 m tf 4P d bf tw tf = - = fyf= fyw 6 m D um * 550 mm 206 mm 6 mm 10 mm 320 MPa = 340 MPa Zx=1362985 mm³ Sx 1533750 mm³ Figure 5 Steel beam under design loads. 6 m P E
Answer in two decimal places please
Only ?% correct solution
A beam has a width of 200mm and a height of 250mm and is loaded as shown. Compute the maximum shear stress. Show computation and present detailed drawings/FBD’s illustrating your solution.
The steel beam has the cross section shown. The beam length is L = 7.3 m, and the cross-sectional dimensions are d = 300 mm, bf = 180 mm, tf = 13 mm, and tw = 7 mm. Calculate the largest intensity of distributed load w0 that can be supported by this beam if the allowable bending stress is 250 MPa.
Higdon
Question (3). Design Exercise (Selecting initial dimensions) A steel cross section of a bridge deck is shown in Figure 3. The cross section is subjected to a maximum bending moment of 43810 kNm. The length L is 4m. Available plate thicknesses (t) are 20 mm, 22 mm and 25 mm. The yield strength () is 355 MPa. Determine the initial dimensions of b and Cw, which can be used for detailed design of the bridge deck. Assume failure of the cross section mainly governs by in-plane bending. State all other assumptions made during this calculations. 60° 2b Ma