The two input terminals of an op-amp are connected to voltage signals of strength 745µV and 740µV repectively. The gain of the op-amp in common mode is 50 and CMMR is 80 dB. Calculate the output voltage and % of error due to common mode.

Q: Problem 6 Find output voltage to the difference amplifier circuit shown in the figure given two…

A:

Q: Given the source voltage v(t) is equivalent to the summation of all component voltages as follows:…

A:

Q: what is the maximum frequency, if the circuit minimum frequency is 7000 Hz and the banwidth is 21…

A: what is the maximum frequency, if the circuit minimum frequency is 7000 Hz and the banwidth is 21…

Q: Problem 4: An AC power supply is connected to a capacitor of capacitance 1.5 μF. At time 0 the power…

A: a)Current through the capacitor is,

Q: Figure 1 shows the circuit diagram of a square law modulator. The signal applied to nonlinear…

A: Output voltage by square law in AM and sensitivity of AM signal

Q: Related Problem Determine the average value of the half-wave voltage if its peak amplitude is 12 V.

A: Peak amplitude Average value of half wave voltage

Q: A 34.1μF capacitor is connected to a 9.7 V, 187 Hz source. What is the capacitive reactance (in…

A:

Q: A 30-µF capacitor is connected across a 60-Hz acsource whose voltage amplitude is 50 V. (a) What is…

A: The capacitance of the capacitor, C = 30 μF = 30×10-6 F The frequency of the ac source, f = 60 Hz…

Q: For what value of the phase angle ϕ between the voltage output of an ac source and the current is…

A: The average power output of the source is given as,

Q: A square wave e is a cyclic pattern that has a constant absolute value, but alternates between…

A:

Q: The input resistance of the LF356 is≈ 10¹2 №, much greater than any resistor likely to be placed…

A: The  is a JFET-input operational amplifier (op-amp) that is known for its high input impedance. An…

Q: 4. When PB2 (NO) is activated momentarily, an analog input voltage, Voin (tag), is sampled every 15…

A: As you can see in rung 0, timer is started using momentary switch pb2 and to run timer…

Q: A single phase 208V AC control power to R=4 2 load if the desired output power is 3 KW, determine…

A: Given data: The voltage supplied, V=208 V. The load resistance, R=4 Ω. The desired output power,…

Q: A common emitter amplifier has a voltage gain of 50, an input impedance of 100 2 and an output…

A:

Q: An unknown load ZL is attached to a 75 Q air-spaced and lossless slotted line. Using a 150 MHz…

A: To calculate the position of the first voltage standing wave minimum on the slotted line, we can use…

Q: Consider a common-emitter BJT amplifier circuit in Figure 3. Assume that Bac = 100 remains constant…

A: Given that, re=10 Ω and β=100. D.C parameters are already given so DC analysis can be skipped. But…

Q: A series RLC ciruit is connected to an AC power source, as shown in the figure. Given that the…

A: The circuit given is series LCR circuit. We know that At resonance maximum current flows in the…

Q: Assuming the R and C values are different for Circuit 1-4, while the value of L and the peak-to-peak…

A: Current is given as Vm/√(R2+(wL-1/wC)2). Peak current is at resonant frequency when wL = 1/wC. So…

Q: A 72.8 F uf capacitor is connected to a 9.3 V, 171 Hz source. What is the capacitive reactance (in…

A: Capacitance of capacitor, C=72.8 μF=72.8×10-6 C RMS value of voltage=9.3 V Frequency, f=171 Hz To…

Q: Q3/ For the emitter-bias BJT find: (a) B; (b) Vcc: (c) RB given the following information: Rc = 2.7…

A: Given : RC=2.7kΩ, RE=0.68kΩ, VCE=7.3V, VE=2.1V, IB=20μA 3)  (a) In an emitter bias BJT, the voltage…

Q: What is the quiescent output voltage of the amplifier shown below? Give your answer in Volts to 2…

A: The dc voltage at an output terminal with reference to a common terminal, normally ground, when no…

Q: For the given circuit for a 40 V (p-p) sinusoidal input vi, what is the value of vi at which the…

A: From the given circuit the diode will be in the forward bias when vi < 5 V. And for vi > 5 V…

Q: 0.75 V, VCE (sat) = 0.3 V, VA = 75 and V₂ = 26 mV. The value of the DC base current I, is The value…

A:

Q: A firing angle controlled triac is feeding a single-phase R-L load with L=15 mH and R=11 ohm.The…

A: A triac is feeding a single-phase R-L load with Voltage  V=220V and 60 Hz Determine: a) Minimum…

Q: Problem 1: A certain circuit breaker trips when the rms current becomes 14.5 A. Randomized Variables…

A: Rms current (Irms14.5 A

Q: A half wave rectifier is connected with a power supply of 50 Hz and provides a peak output voltage…

A: Answer..

Q: difference amplifier circuit

A:

Q: 26. (a)Design a band stop filter using RC components that will only allow a range of frequencies to…

A: Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: ) The RC circuit below is hooked up to a source that provides an emf of e(t) = Vocos(wt), where Vo =…

A: a) The impedance of the circuit is, ZR2+1ω C2 Here  =1002+11008×10-62=328.1Ω

Q: e of 70 pF when an a

A:

Q: (b) In a Common Emitter BJT amplifier, a capacitor CE is included and in a Common Source JFET…

A: Common Emitter BJT Amplifier- Transistor amplifier’s increase an AC input indicators that alternates…

Q: Considering a frequency-division multiplexing system where a baseband signal from sending end is…

A: The corresponding RC bandpass filter is shown below:

Q: 7. What is the RMS voltage of a square wave with a 50% duty cycle that swings between ±5?

A: