The two balls are attached to the light rigid rod, which is suspended by a cord from the support above it. If the balls and rod, initially at rest, are struck with the force F = 11.7 lb, calculate the magnitudes of the corresponding acceleration a of the mass center and the rate at which the angular velocity of the bar is changing. T 8.0" + 3.6" T 5.1" 10.2" Answers: ā= Ö= Mi Mi 4.18 lb 2.93 lb ft/sec² rad/sec²

The two balls are attached to the light rigid rod, which is suspended by a cord from the support above it. If the balls and rod, initially at rest, are struck with the force F = 11.7 lb, calculate the magnitudes of the corresponding acceleration a of the mass center and the rate at which the angular velocity of the bar is changing. T 8.0" + 3.6" T 5.1" 10.2" Answers: ā= Ö= Mi Mi 4.18 lb 2.93 lb ft/sec² rad/sec²

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Consider a slender rod AB with a length l and a mass m. The ends are connected to blocks of negligible mass sliding along horizontal and vertical tracks. If the rod is released with no initial velocity from a horizontal position as shown in Fig.A, determine its angular velocity after it has rotated through an angle of θ (see Fig B) using the conservation of energy method. (Hint: Moment of inertia of rod about G = (1/12)ml2 The kinetic energy of a rigid body in plane motion is
The 14.6-lb lever OA with 9.6-in. radius of gyration about O is initially at rest in the vertical position (0 = 90°) where the attached spring of stiffness k = 4.3 lb/in. is unstretched. Calculate the constant moment M applied to the lever through its shaft at O which will give the lever an angular velocity w = 5.9 rad/sec as the lever reaches the horizontal position = 0. k= 4.3 lb/in. 13.6"- M G 6 7.6" 13.6"
The 18-kg rod AB is pin-connected at A and subjected to a couple moment of M =15 N- m The rod is released from rest when the spring is unstretched at 0 = 30°. As the rod rotates, the spring always remains horizontal, because of the roller support at C. (Figure 1) Determine the rod' s angular velocity, measured clockwise, at the instant 0 = 60°. Express your answer using three significant figures. Enter positive value if the angular velocity is clockwise and negative value if the angular velocity is counterclockwise. vec rad/s k = 40 N/m 0.75 m M = 15 N- m
6. (D34Q2) The 18-kg wheel is initially at rest and then starts rolling without slipping under the constant force of 300 N through the handle as shown. If the wheel has mass center at point G and the radius of gyration is ke=0.3 m, determine its angular velocity after 2 seconds. You must use impulse and momentum to solve this problem. G r=0.5 m 10° 300 N
25
The 2.28-kg uniform slender bar rotates freely about a horizontal axis through O. The system is released from rest when it is in the horizontal position 0 = 0 where the spring is unstretched. If the bar is observed to momentarily stop in the position 0 = 66°, determine the spring constant k. For your computed value of k, what is magnitude of the angular velocity of the bar when 0 = 48°. B 0.85 m 0.85 m 2.28 kg 0.29 my Answers: k = i N/m ω- rad/s 1
The two balls are attached to the light rigid rod, which is suspended by a cord from the support above it. If the balls and rod, initially at rest, are struck with the force F = 10.7 lb, calculate the magnitudes of the corresponding acceleration a of the mass center and the rate θ¨ at which the angular velocity of the bar is changing.
The shown body is composed of a disk with mass 10 kg and a slender bar with mass 5kg which is released from rest form the 4m Im horizontal condition (it is released when 0 = 0). calculate the angular velocity and angular acceleration and the forces at the hinge point (Point O) when 0 = 60 deg. Length of bar is 4m and the radius of disk is Im.
The system is at rest with the spring unstretched when theta = 0. the 5.3 kg uniform slender bar is then given a slight clockwise nudge. The value of b is 0.45 m. (a) if the bar comes to momentary rest when the angle = 58, determine the spring constant k. (b) for the value k = 65 N/m, find the magnitude of the angular velocity of the bar when the angle = 38 degrees. a) k = 70.634 N/m
The system shown below consists of a uniform disk D that has a mass of mp = 3.0 kg and a radius of r = 1.0 meters. The disk is connected by a massless cable to a block. The system is released from rest and the disk starts rolling without sliding with the angular acceleration of a = rad 30 s2 in the clockwise direction. Determine the magnitude of the friction force (in Newtons) developed between the disk and the inclined surface at this instant. Consider 0 = 40° and g = 10 m. mp
Part A The 100-kg spool is resting on the inclined surface for which the coefficient of kinetic friction is uz = 0.12. The radius of gyration about the mass center is kg = 0.25 m (Figure 1) Determine the angular velocity of the spool, measured clockwise, when t = 6 s after it is released from rest. Express your answer using three significant figures. Enter positive value if the angular velocity is clockwise and negative value if the angular velocity is counterclockwise. VO A£¢ !f vec ? W = rad/s Figure 1 of 1 > Submit Request Answer Provide Feedback Next > 0.4 m 0.2 m 30°
A cable is wrapped around the spool’s center hub. The mass of the spool is m= 100 kg, the radius r1 = 0.4 m, r2 =0.6 m, and the radius of gyration is kG = 0.3 m. A horizontal force P = 10 N is applied to the cord. The spool is initially at rest and rolls without slipping. (3) The angular velocity of the spool after 2 seconds is __________rad/s (two decimal places)