The truss shown its subjected to the forces P = 64 kN, lenght L = 12 m divided in equal separations and height H = 1.6 m. Determine the magnitude of force in element 1. |P |P |P IP |P H

Q: Part of the screw thread connecting the adjacent flank on top of the screw thread is known as O…

A: Correct answer is option (b) Pitch  The pitch of a thread is the distance measured parallel to its…

Q: What about Mohr's circle?

A: In the previous question, Given: The diameter of shaft, d = 20 mm = 0.02 m The maximum bending…

Q: Write the formula for the time required to fill the cavity by the bottom gating system.

A: Given: Bottom gating system

Q: DRAN THE 1SOME TRG VIEW

A: Isometric view for the given orthographic views is drawn on the isometric grid paper. 1 Grid = 1…

Q: State the difference between the eutectic and eutectoid points.

A: Eutectic point: In the iron carbon phase diagram at 2 percentage of carbon is called eutectic point.…

Q: Differentiate between single acting and double acting cylinders.

A: Differentiate between Single Acting & Double Acting Cylinder :

Q: Describe the Spherical Vessel?

A: A vessel is a closed structure containing liquids or gases under pressure. Familiar examples include…

Q: Consider the shaded area in (Figure 1). Take a 520 mm. Figure 150 mm 150 mm 100 mm 300 mm Determine…

A: The distance a=520 mm

Q: Each cylinder in a four-cylinder car engine has a bore diameter of 63.53 mm and the stroke for each…

A: Consider a vehicle engine where number of cylinder are situated whose bore diameter is D and stroke…

Q: 30o0mm*300 mmXJ0omm

A: Given data :- 300mm × 300mm × 300mm  Compare L × b × h  Here L= length           b= width…

Q: A motorcycle drives off a ramp of height S (m) at an angle of 0• and speed u (m/s) as shown below.…

A:

Q: Why is it called Mohr's circle?

A: Mohr’s  circle is graphical representation which enables us to visualize the relationships between…

Q: tan30*sin30

A: Given, Value of tan30 and sin30 is, tan30°=0.577sin30°=0.5

Q: Where did the 0.10472 rad/s come from?

A:

Q: -d12 The figure shows a tabletop experi- nent that can be used to determine an unknown homent of…

A:

Q: Customary units by using the values listed for length and mass as defined values: Bending moment or…

A: As moment bending moment or torque has two variables, force and distance. So, M = F × r…… (1) The SI…

Q: RIS R12 frant sew R32

A: Given 3D model To find Three views

Q: can you Reslove?

A: To solve the problem you have typed in, follow these steps: Analyze the given data:L2 = 6Q2 = 35…

Q: = The cross-section of a wooden, built-up beam is shown below. The dimensions are L w = 20 mm.…

A:

Q: When does a couple of moment work?

A: A couple is when a system of forces has no net force but has a net moment. A couple causes pure…

Q: d W Pm a Ps

A: The free body diagram of the system is showing below –

Q: Y 8 12 8 12 R= 3

A:

Q: where do you get the form factor (y=.337) from? Please.

A: Form factor for full depth 20° at 24 teeth can be taken from standard table. I have provided the…

Q: b) Determine the March number of the bullet for both medium.

A: (b) Consider the helium gas and calculate the speed of sound in helium. cHe=γRTMFor γ,…

Q: 2 Brass expands more than iron when heated. How would the strip look after prolonged exposure to…

A:

Q: Consider the bracket shown in Fig-3. If: • F1 = 10 lb @ -90° • a = 2 ft •b = 4 ft • c= 1 ft then,…

A: Consider the free body diagram of member AC, Here,

Q: how do you know where the point 2 is ? or how do you find point 2

A:

Q: 1. Uf this drawing? 2. What is the name of the company responsible for the drawing? 2. MILWAVKEE…

A: Given :-  9.The drawings are shown in what angle

Q: Draw the front, Side and top

A: According to the question we need to draw the three orthographic projection views of the given…

Q: 4. The weight of the box is W = 90 N and the coefficient of static friction between the box and the…

A:

Q: It is observed that the density of an ideal gas increases by 10 percent when compressed isothermally…

A:

Q: Reselve the 4501b fovce intoeom ponentsacting atong members ABandAC 30 45 450

A:

Q: Isn't the area of the circle equal to pi times the square of its radius?

A: Explanation: Since the diameter ( d )  of steel bar is given, area of the circle is in terms of…

Q: what is the actual area in part a ?

A: Given: Q=5000 m3/min=5000m3min×1min60 sec=83.33 m3/s V=6.0 cm/s=6.0cms×1m100cm=0.06 m/s

Q: non exact .3

A:

Q: 5と 2' 111ド 7K 8'一 16- 251

A:

Q: For machine element, locate the centeroid

A: Answer:  Centroid ( 44.78 , 27.19 , 26.25 ) For a step-by-step solution have a look through the…

Q: 2. Orientation is the general term used to describe the features. O linear O most important…

A: The meaning of orientation in terms of relationship between features is to be chosen from given…

Q: Consider the bracket shown in Fig-3. If: • F1 - 10 lb @ -90° • a- 2 ft • b- 4 ft • c-1 ft then, what…

A: