The truss in the figure is loaded by four external forces as shownbelow. Knowing that P1= 3 kN, P2-4 kN, P3-6 kN and P4=2 kN, a= 3 mand h=2 m, you are required to:hP1P2aHBmembers GH, BG, BC.IP3GCP4FDa --- a -- aa) Determine the reactions at the supports A and E.b) Using the method of joints, determine the forces of themembers at joint A.c) Using the method of joints, determine the forces of themembers at joint E.d) Using the method of sections, determine forces onmembers GF GC, CD.e) Using the method of sections, determine forces onP1Note: You are required to draw the FBD and apply the equilibriumequations for each case.E

Note: As per the policy, we can solve the first 3 subparts. Please resubmit the remaining parts.

Answered: The truss in the figure is loaded by…

The truss in the figure is loaded by four external forces as shown below. Knowing that P1= 3 kN, P2-4 kN, P3-6 kN and P4=2 kN, a= 3 m and h=2 m, you are required to:

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

2- Find the applied force by the hydraulic cylinder in the truck shown graphically using KS: 1cm=1m, KF: 1cm=1 kN. W=25 kN
Homework Q1/. Three cables are joined at the junction ring C. Determine the tensions in cables AC and BC caused by the weight of the 30 kg cylinder. See figure (1). Q2/. Determine the reactions on the bent rod which is supported by a smooth surface at B and by a collar at A, which is fixed to the rod and is free to slide over the fixed inclined rod. See figure (2). Q3/. The portable floor crane in the automotive shop is lifting a 420 lb engine. For the position shown compute the magnitude of the force supported by the pin at Cand the oil pressure p against the 3.20 in-diameter piston of the hydraulic-cylinder unit AB. See figure (3). A 42 45° 100 Ib 18 15 3 ft 30 200 lb ft 30" 30 30 kg 2 ft 13 6" Fig (1) Fig (2) Fig (3)
Member AB is supported by a cable BC and at A by a square rod which fits loosely through the square hole in the collar fixed to the member as shown in the figure. Suppose that F1 = 190 N, F2 = 390 N and the rod holds in equilibrium. Determine the components of reaction force at A using scalar notation and tension in the cable. Determine the components of the moment of reaction at A using scalar notation.
4.) The uniform 4-kg rod AB is supported by a ball-and-socket joint at A and by the cord CG that is attached to the midpoint G of the rod as shown in the figure. The rod leans against a frictionless vertical wall at B. Determine the reactions at A and B and the tension in cord CG. [Answer: T = 20.8 N, Ax= -14.7 N (down), Ay= 29.4 N, Az 11.0 N, B= 29.0 N, where the positive answer indicate the reaction goes in the positive direction of the respective axis and vice versa] Hints: Note the given mass from which you need to calculate weight. IF G is is the midpoint of the rod, then the x, y, z coordinates of that point can be taken to be half the x,y,z components of the position vector FAB 150 mm, B 400 mm 0 150 mm 600 m G
Find the horizontal and vertical reactions at the pin at B. Note that the support at D is fixed. Sign convention for the positive x and y direction applies for the answers. Diagram not to scale Answers: (a) -4 kN, 2 kN (b) 4 kN, -2 kN (c) 1.5 kN, 3 kN (d) -1.5 kN, -3 kN 3 kN B A D TTT 2 m 4 kN 2 m C 1m 2 m 5 m
Problem: The elements of a wall-mounted swing-away stool are shown in the figure. The hinge-pin P fits loosely through the frame tube, and the frame tube has a slight clearance between the supports A and B. Determine the reactions on the frame tube at A and B associated with the weight L of an 80 kg person. Also, calculate the changes in the horizontal reactions at C and D due to the same load L. State any assumptions. 65 mm Al 175 mm B 65 mm D 350 mm 85 mm
For Probs. 1-3, (a) draw the free-body diagrams for the entire assembly (or structure) and each of its parts. Neglect friction and the weights of the members unless specified otherwise. Be sure to indicate all relevant dimensions. For each problem, (b) determine the total number of unknown forces and the total number of independent equilibrium equations. Problem 1 500 N 500 N 1 m 500 N (b) (c) Figure 1 Problem 2 -- Ift 4 ft -1.8 ft 100 lb F1.8 ft - 100 lb 100 lb (а) (b) (c)
The uniform rod AB has a mass of 140-kg and it is supported as shown in the figure. If the applied force F= 1.4 kN, what is the reaction at A on rod AB? Assume frictionless surfaces. 1.5 1.5 0.9 m 0.9 m
Find the force in each member of the truss shown below. Be sure to state whether the member is in tension or compression. 8 ft B 375 lb A C 16 ft-+ 8.2 ft 500 lb OD