a) 1c) 0.3b) 417. The value of k that gives a peak time T, equal to see isnThe Transfer function T (S) = 52 +45+kAnswer the following questions (17-19)√ sec isb) 118. The value of damping ratio & that gives a peak time T, equal to0.436a)c) 0.667Given that k =5, then the steady state error for unit step inputa) 0.0b) 0.2c) 0.819.d) 21d) 1.23d) ∞e) Nonee) Nonee) Nonecontrol system seen in the figure, the resulted output from the following responses.

Answered: Image /qna-images/answer/f8904b24-280c-4f50-a551-5f6179c01a55.jpg

Answered: The Transfer function T(S)

Engineering

Electrical Engineering

The Transfer function T(S)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

a) Design a circuit using 741 op amp IC and 555 timer IC, to generate both Pulse Width and Pulse Position modulated signals. Perform the required calculations to obtain the width of the PPM signal as 200μs. Draw the clear circuit diagram and calculate the values of resistors and capacitors used. b) Simulate the circuit designed in part (a) using appropriate simulation tools(Multisim or Tinkercad) and obtain the output. The answer should include details such as aim, brief procedure, screenshot of simulation circuit along with resultant waveforms and calculations of the practical time-period obtained for PPM output. c) Plot graphs with clear labels and scales for message, carrier and output signal (PWM and PPM). Also discuss your inference and reflection on the results obtained. [Note: Plot graphs on a normal graph paper by hand and attach the scanned copy to the assignment]
Autesave For revision session ) - Protected View Saved to this PC P Search (AltQ Natasha Keery File Home Insert Draw Design Transitions Animations Slide Show Record Review View Help Record Present in Teams eShare O PROTECTED VIEW Becrefles from the Intenet.can contain vinnen. Unles you need te edit safr to stey in Protected Vie. Enable iditing 14 Example 15 For the comparator circuit shown below, a a sinusoidal input signal with a peak voltage (Vp) of 5 V and a frequency of 1 Hz is applied to the non-inverting terminal. Assuming that the signal frequency is well below the slew rate limit, describe and draw what would be the comparator output. Assume values of +Vcc as +10V and -Vec as -10 V, with the corresponding output saturation voltages of +V of +9 V and -V of -9 V. 16 17 18 19 Sde 1of 24 English united Kingdom ENG 014 210/2022
Answer the following questions for the given Question electrical system in the figure: ell I(s) a) Write the transfer function Vin(s)' b) Time constant of this circuit is 0.002sec and resistor has a value of R=5 Q. Calcule the inductance value L. c) Obtain the steady-state value of the current i(t) by using final- value theorem when the Vin = 5 Volt. d) Draw time response of the current i(t) when Vin = 5 Volt while indicating current values i(t) at the multiple values of the time V. R V. out in constant.
The amplitude to the derivative input circuit given in the figure is peak to peak Vpp=2Volana) A 1kHz sine wave signal is applied. Draw the waveform by making a mathematical analysis of the output voltage (Vo). Interpret your results.b)A 1kHz square wave signal is applied. Draw the waveform by making a mathematical analysis of the output voltage (Vo). Interpret the results you have obtained. (Opamp supply±12V) Derivative Circuit
a) Reduce the following block diagram (Figure Q2) to a single transfer function C(s) T(s) : R(s) C(s) R(s) 1 NC NC NC 5 3 2 NC 3 Figure Q2 b) Convert the block diagram of FigureQ2 to a signal flow graph and find transfer function using Mason's rule
Nowadays switching power supplies are commonly used because they offer better efficiency and smaller size compared to a linear power supply, because high switching frequency allows for smaller transformers. One place to find a SMPS (switching mode power supply) is a phone charger. Switching power supplies cause high frequency noise on switching transients. The noise on the output is filtered in various ways but savings may be considered on the output filter (extra inductors and capacitors = extra costs), which means the output will have some amount of noise left getting to the device via the USB cable. Estimate the frequency where the phone charger starts to act as an antenna when the USB cable length is 1.9 meters. Submit your answer in MHz without the unit, rounded to one decimal place. Hint: Either "rule of thumb" can be used.
(b) Figure Q1(b) shows the step response for a second-order system. Find its peak time and percentage of overshoot. Hence, obtain its transfer function. 1.6 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0.0 0. 6 10 12 14 16 18 20 22 24 Time (s) Figure Q1(b) Response
a) Describe with the aid of suitable diagrams, the three types of stable output response to a step input produced by a second order system. b) The step response of a second order system is shown in Figure Q6. Magnitude 3 Result of Instruments Step Response 2.75 mmmm mm mm mm I 1.5 3 c) 2 1 ww www www m 1900 1999 1998 199988 0.5 1 Percentage overshoot Time to the first peak Damping factor, < Undamped natural frequency, wn 0 0 Find the: i) ii) Find the: i) ii) 2 Time (seconds) Figure Q6 2.5 3.5 4
Question 1: A) Derive the transfer function of the electrical circuits shown in Figure below and then show the output signal when the input is a unit step. V₁(s) Vc (s) V(s) elle Ls -18
please provide sketch!!!!! Please answer in typing format please ASAP for the like please
Q9 The discrete-time signals x1[n] is shown in the figure. Carefully sketch each of the following signals: a) x1[2n] - u[n-2] b) x1[n]*u[1-n] c) x1[-2n-3] (d) Compute the signal energy 3 2 -1 *x[n] 1 10 1 2 3
b) Create a new folder name Lablb in your D:\Student_Matric_Number. Find the output X and show the simulation waveform. A B