The total radiation energy received normally from the sun per unit time per unit area is called Select one: O Lunar Constant Solar Photons O Solar Irradiance O Solar Radiation Temperatures at the center of earth are around degrees centigrade.

Q: turn loads fully ON or fully OFF. a. Analog circuits b. Contactors c. Digital circuits d. Mechanical…

A: In this question we need to choose a correct option

Q: VExplain parameters that increase fault conductivity?

A:

Q: Generation engineers are more inclined to an operation in a closed system as compared to an open…

A: Nowadays Electricity is a major part of any country's growth. The demand for power supply is…

Q: In 4-point starters the resistance is added in series with NVC because __________________ a) To…

A: At the starting of the motor, Back emf (Eb) will be zero, hence a very high current flows through…

Q: List the minimum trade size Type EMT for each of the following applications. (Objective 12-1)…

A: As per Bartleby expert policy only first individual question is to be answered. So, answering only…

Q: (a) Explain the following picture and its' importance in selection of circuit breakers Extinction of…

A: Electrical power systems require some switchgear that can be controlled with ease and regulate with…

Q: explain Cell Relay with its application

A: Cell relay is a network technology used for transmission of data by using small data packets of a…

Q: Draw a simple block diagram of 'Open-Loop Control System' and 'Closed-Loop Control System' Not…

A: CS - control system

Q: Explain thevenin equivalent circuit for dummies?

A: ELECTRICAL NETWORK: When addressing a circuit problem or constructing a balanced circuit, the word…

Q: WHAT NAME IS GIVEN TO TYPE OF MANUFACTURE OF SINGLE ONE OFF COMPONENTS

A: One off manufacture is the manufacture of a single product or item which can include specialist…

Q: Compare between armature resistance and synchronous resistance.

A:

Q: ow does an intermediate switch work?

A: The explanation is as follows.

Q: With neat diagram explain the principle and working of motor used in lifts. Prepare 1 page word…

A: Lift uses traction procress. DC series motor were used for traction before, because it has high…

Q: 4 For the closed-loop control system described by the block diagram shown in figure below. determine…

A:

Q: Identify the system which has low stability. a. None of the above b. Open loop and Closed loop…

A: Consider the open loop control system: In this the control system depends only on the input and is…

Q: For the Starting Up the Power Station Simulator Why are certain operations blocked by isolators

A:

Q: 4 A 100KW, belt driven shunt generator running at 300rpm on 220V bus bars continue to run as a motor…

A:

Q: Draw the symbol of Relay operation (off) Draw the symbol of Relay operation (on)  Draw the symbol…

A: The symbol of the delay relay operation (off) is The symbol of the delay relay operation (on) is

Q: Explain the different type of routin test In CB ??

A: There are different kinds of routine tests done for the Circuit Breaker.   Power frequency…

Q: Automatic voltage regulator will have the ability to maintain the a. Nose point - that can be…

A: Automatic voltage regulator is a solid state electronics device used for maintaining generator…

Q: 13. To ensure an adequate factor of safety in the of a shaft with standard keyway, the key width I…

A: Key : It is a piece of mild steel inserted between the shaft and hub or boss of the pulley to…

Q: Q)Write a report about relay and the difference between relay and contactor?

A: consider the given question;

Q: . Question Calculate the values of the parameters K1 and K2 in order for the closed loop system,…

A: Routh Hurwitz

Q: motor driven conveyors. Before entering the bottles are rejected. Draw ladder diagram to achieve…

A: Please find your answer below in step 2

Q: Explain with a neat block diagram the measurement of displacement using RTD (measuring system).

A: Thermistor is a special type of Resistor whose resistance changes with the change in temperature.…

Q: An attenuator used in control systems unit is also known as _________?   A. Summing amplifier…

A: In the control system attenuator is used to control diminish  signals flowing between different…

Q: Write an introduction about Relays Your introduction should include the following points: A-What is…

A: A) Relay: It is a device that acts as a switch. It works on the electromechanical principle in which…

Q: Explain the validity and suitability of the electrical safety components Emergency Stop Switches.…

A: Emergency Stop Switches:- A fail-safe control is an E-stop switch, often known as an emergency stop…

Q: Explain brownout and its difference to blackout

A:

Q: Why is proper grounding important?

A: Ground potential:  Ground potential has zero reference level used in a system to measure and apply…

Q: is measured by the voltmeter and the unit is Volt ect one: True False

A:

Q: what is the STOP W.O.K.E Act

A: Florida state legislature, with the support of Republican Government- ‘Ron DeSantis’. passed a new…

Q: 2-2.A machine placed in a vigorous tidal stream might reach its rated power at a stream speed of 5.9…

A:

Q: Give a brief description for under/over voltage time relay.

A:

Q: What is light triggering method?

A: A SCR (Silicon Controlled Rectifier) also known as a semiconductor controlled rectifier is a current…

Q: what is  protective relaying? what is Time & Setting Multiplier ?

A: What is  protective relaying? A protection relays is a switching equipment which detect faults and…

Q: What are the advantages of high voltage transmission?

A: Introduction The bulk transfer of electrical energy from generating power plants to electrical…

Q: For the systems enumerated below, indicate whether they are open-loop or closed-loop control…

A: For the systems enumerated below, indicate whether they are open-loop or closed-loop control…

Latches and Flip Flop

Just like logic gates, the latches and flip-flops are the important elements of an electronic circuit. The logic gates form the important part of combinatorial circuits, while the latches and flip-flops form the essential part of a sequential circuit. Sequential circuits form the important concept of automata theory in electronics and electrical engineering, these circuits are a kind of logic circuit whose output depends on both present input and past inputs, that is, the input history.