The top of the tower signal at B 2000 m away from A was sighted through a transit with a recorded vertical angle of 3'30". The height of the mast is 12 m and H.I. of the transit above the point where it is set is 1.10m. The elevation of the point under the transit A is 133.33 m. Compute the elevation of the base of the signal B. 545.025m 355.025m 245.025m 445.025m

The top of the tower signal at B 2000 m away from A was sighted through a transit with a recorded vertical angle of 3'30". The height of the mast is 12 m and H.I. of the transit above the point where it is set is 1.10m. The elevation of the point under the transit A is 133.33 m. Compute the elevation of the base of the signal B. 545.025m 355.025m 245.025m 445.025m

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

12.a. You're working on an installation at a patient care facility. You have two panelboards next to eachother that supply the critical and the normal feeder circuits. These two panelboards must be bondedtogether using an insulated copper conductor with a minimum size ofA. AWG 10.B. AWG 6.C. AWG 8.D. AWG 4. 12.b. You're installing an isolated power system in a hospital that'll serve a group of patient care areas. Whichof the following colors must be used for the wire that connects to the terminal at each receptacle that'susually reserved for the neutral conductor?A. Green with a white stripeB. Orange with a distinct stripeC. Red with a black stripe
1. The terms “open-circuit", “short circuit" and “dead short" are used in speaking electricity. Answer the following questions about these three terms: a. What is the value of the resistance of an open circuit? b. What is the value of the resistance of a short circuit? c. What is meant by a “dead short"? 5 DDPasalo-Electrical Engineering Department COE MMSU EE 121: Electrical Circuits I 2. When a switch is open, is the resistance between its terminals high or low? ¸Low 3. What is the resistance of a closed switch (ideally)? 4. Using each of the methods shown in (a) and (b) below, calculate the value of the equivalent resistance of a combination of R1 = 5 ohms and R2 = 20 ohms connected in parallel a. Using the equation: 1/Requivalent = 1/R, + 1/R2 + 1/R3 = b. Using the equation: Requivalent = (R, x R2) / (R, + R2) = Ω
21 Q2/ The one Per-unit impedaunce digram line digram 3-Phave pouser System. Draw the G: 50 MVA, 13.2 KU , Xg = 0.2 Pu Tig 30MVA , 13.2/220KU, XT,=0-1s P4 Te 30MVA, 22./11 kU, X+Z=0.15pu T3:30MVA , 13.2/132 kv, XT,=0.15P4 Tu:30MUA 132/11 KV, XTzo.15 Pu M: 70 MVA, lo.45kv, Xm =0.2 p4 Load, 53 MVA , lo.45kv, o.7 P.R (Lag) line1: 22o ku, Xline I=4oA %3D line2: 132 kv, Xlinez = 6or Te 220 132 36 Ty load 38 Select a Common base of 90MUA ,13.2kv on the generator Side
Describe series and parallel circuits. Which is used in building electrical systems?
Q2.A/ Write the number and its suitable letter. There are two extra letters you do not nee use. 1. call 2. pick up 3. fitness 4. make 5. give A. the phone B. somebody a call C. a trip D. sure E. a message F. centre G. somebody back 2. 3. 4. 5.
2- Thermosyphon is a. Direct system b. In direct system c. Active d. Pumped Direct System 3- The hydrogen-based power supply system does not pollute the environment. We start with water And we're done with ------ a. solar power b. energy c. electiric power d. water
Convert 214 ºF to engineering notation using the appropriate SI unit. (You must provide an answer before moving to the next part.) 214 ºF in SI unit using the proper engineering notation is written as K.
1- The recommended limit of voltage drop on a lighting circuit for a single-phase supply as per IEE Wiring regulations is equal to 6.3 volt. Then the value of supply voltage is a. 290V b. 250V c. 210V d. 230V 2- Which of the following statement is TRUE ? a. Resistance is not proportional to length of the material and Resistance is proportional to area b. Resistance is proportional to length of the material and Resistance is proportional to area c. Resistance is not proportional to length of the material and Resistance is inversly proportional to area d. Resistance is proportional to length of the material and Resistance is inversly proportional to area
3- Assume you are a health safety environment engineer and you are working in an oil field. Explain the details about mechanical and electrical hazards in oil and gas field. Support your answer with an example of each.
Draw the signal flowchart of the simple resistance network shown below. a) Determine the variables.b) Establish relationships between variables (circuitusing rules).c) Identify branches and nodes and signal flowDraw the timetable.
The internal resistance of an ideal voltage source is _____. * A. Infinite B. Equal to the load resistance C. Zero D. To be determined
Discuss the concept of electrical substations and their function within a power system.