The tire wrench shown in the accompanying figure is used to tighten the bolt on a wheel. Given the information on the diagram, determine the moment about point O for the two loading situations shown: a. pushing perpendicular to the wrench arm, and b. pushing at a 75° angle, as shown.

The tire wrench shown in the accompanying figure is used to tighten the bolt on a wheel. Given the information on the diagram, determine the moment about point O for the two loading situations shown: a. pushing perpendicular to the wrench arm, and b. pushing at a 75° angle, as shown.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The figure below shows a small gate attached to two couplers. The door needs a resultant moment of 178 N-m counterclockwise to be able to open when rotated around pivot A. The purpose of this problem is to calculate the force F2 needed for the door to open with the specified moment. The magnitude of the force F1 is equal to 480 N (Note that due to the distances provided, it is not necessary to use the principle of moments for couples and not all dimensions will be needed). What is the magnitude of the force F2 necessary for the gate to open? This will be the answer that will be offered in the numerical entry of this question.
Figure Q1(b) shows the loading system. Determine the loading system acting on the post by an equivalent resultant force, magnitude, direction and moment at point A. (Ignore the support reaction)
An experimental device imparts a force of magnitude F = 32 lb to the front edge of the rim at A to simulate the effect of a slam dunk. Compute the moment of the force F about point O and about point B. The moments are positive if counterclockwise, negative if clockwise. Finally, locate a point C from the base at O to the location on the ground where the force imparts zero moment. The distance d from point O to point C is positive if C is to the right of O, and negative if to the left. Assume a = 36 in., b = 28 in., h = 12 in., H = 10 ft, c = 5, and d = 7. Answers: Mo= i Mg = i d= i B b H F lb-ft lb-ft ft
A 7 m long steel shaft weighing 250 kg is supported at points A and B as shown in the figure. If the weight of the shaft acts at point G, determine the moment of the weight about point A in Cartesian form. Assume the point G is located at the coordinates (1m,3m,1.5m) & if the support at B creates a reaction force Bx and By as shown, determine these reaction forces. Assume B is located at 3 m from the origin O along the z-axis
The specialty wrench shown in the figure is designed for access to the hold-down bolt on certain automobile distributors. For the configuration shown, where the wrench lies in a vertical plane and a horizontal 290-N force F is applied at A perpendicular to the handle, calculate the moment Mo applied to the bolt at O. For what value of the distance d would the z-component of Mo be zero? Assume a = 85 mm, d = 155 mm, h = 150 mm, 0 = 28° F Answers Mo = ( i d = i 0 h i+ i mm j+ i k) N.m
An experimental device imparts a force of magnitude F = 32 lb to the front edge of the rim at A to simulate the effect of a slam dunk. Compute the moment of the force F about point O and about point B. The moments are positive if counterclockwise, negative if clockwise. Finally, locate a point C from the base at O to the location on the ground where the force imparts zero moment. The distance d from point O to point C is positive if C is to the right of O, and negative if to the left. Assume a = 36 in., b = 28 in., h = 12 in., H = 10 ft, c = 3, and d = 7. Answers: Mo= MB= d = i i i a h B b H F lb-ft lb-ft ft
The port hull of a catamaran (top view shown) has cleats at points A, B, and C. A rope having 100N force is to be attached to one of these cleats. If the force is to produce the largest possible counterclockwise moment about point O, determine the cleat to which the rope should be attached and the direction the rope should be pulled (measured positive counterclockwise from the positive x direction). Also, determine the value of MO produced. Assume all cleats, point O, and the rope lie in the same plane.
Problem 4-Frames & Machines The gripper shown to the right has a broken torsion spring at point C which, therefore, does not contribute to the moment about point C. It is as if it isn't there. Using this information and the grip forces shown, determine the gripping force applied to the scrap at point H. Model the reaction(s) as acting parallel to the 5 lb gripping forces. 2 in. B 4 in. 5 lb 5 lb 12 in. 2 in. F E 3 in. H
and For problem above, Replace the loading on the system below by a single resultant force. Find the points on the x- and y – axes through which the resultant force must pass.
The light boom AB is attached to a vertical wall by a ball and socket joint at A and supported by two cables at B. A force P is applied at B where P = 19i - 10j kN.Note that the reaction force at A acts along the boom because it is a two-force member. Magnitude of the reaction force at A in kN = 34.8 Determine the magnitude of the moment of P about the x-axis in Nm
The specialty wrench shown in the figure is designed for access to the hold-down bolt on certain automobile distributors. For the configuration shown, where the wrench lies in a vertical plane and a horizontal 150-N force F is applied at A perpendicular to the handle, calculate the moment Mo applied to the bolt at O. For what value of the distance d would the z-component of Mo be zero? Assume a = 90 mm, d = 130 mm, h = 210 mm, 0 = 16% F Answers Moi d= Mi 0 h i+ mm Mi j+ Mi k) N.m
help me pls :(ignore the values in the picture and substitute it with the ones in the problem