The three-reservoir system is shown below: The elevation of Reservoir at A is 130m and at C is 30m. The flow rate at Pipe 1 from Reservoir A is 2.1 m/s. All pipes have a length of 500 meters, friction factor f = 0.02, and sizes namely: Pipe Diameter 1 (mm) = 600mm Pipe Diameter 2 (mm) = 500mm Pipe Diameter 3 (mm) = 400mm Show a solution sheet containing the following: 1. Headloss at Pipe 1 2. Headloss at Pipe 3 3. Flow rate at Pipe 3 4. Flow rate at Pipe 2 5. Headloss at Pipe 2 6. Elevation of Reservoir B

The three-reservoir system is shown below: The elevation of Reservoir at A is 130m and at C is 30m. The flow rate at Pipe 1 from Reservoir A is 2.1 m/s. All pipes have a length of 500 meters, friction factor f = 0.02, and sizes namely: Pipe Diameter 1 (mm) = 600mm Pipe Diameter 2 (mm) = 500mm Pipe Diameter 3 (mm) = 400mm Show a solution sheet containing the following: 1. Headloss at Pipe 1 2. Headloss at Pipe 3 3. Flow rate at Pipe 3 4. Flow rate at Pipe 2 5. Headloss at Pipe 2 6. Elevation of Reservoir B

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Two reservoirs are connected by two parallel pipes of equal length and of diameters 20 cm and 10 cm, as shown in the figure (not drawn to scale). When the difference in the water levels of the reservoirs is 5 m, the ratio of discharge in the larger diameter pipe to the discharge in the smaller diameter pipe is (Round off to two decimal places) (Consider only loss due to friction and neglect all other losses. Assume the friction factor to be the same for both the pipes) ! Reservoir 5 m 20 cm 10 cm ļ Reservoir
Two reservoirs are connected by two parallel pipes of equal length and of diameters 20 cm and 10 cm, as shown in the figure (not drawn to scale). When the difference in the water levels of the reservoirs is 5 m, the ratio of discharge in the larger diameter pipe to the discharge in the smaller diameter pipe is (Round off to two decimal places) (Consider only loss due to friction and neglect all other losses. Assume the friction factor to be the same for both the pipes) ! Reservoir 5 m 20 cm 10 cm ļ Reservoir
8. Water is flowing in a 100 mm diameter Mild Steel (MS) pipe of length 180 m as shown in the figure. The reservoir water level remains constant. Determine the flow rate. Use the following methods: (a) Darcy Weisbach formula with loss coefficient method, (b) Darcy Weisbach formula with effective pipe length method, (c) Hazen William's formula with loss coefficient method, and (d) Hazen William's formula with effective pipe length method. (Ans.: 28.27 liter/s, 28.33 liter/s, 32.04 liter/s, 32.67 liter/s) EL85 m EL = Elevation Gaie valve Butterfly valvé opened EL50 m
Two sharp-ended pipes of diameter d₁ = 50 mm, and d₂ = 100 mm, each of length 100 m, are connected in parallel between two reservoirs which have a difference of level h= 10 m, as shown in figure below. If the friction coefficient, f= 0.032 for each pipe, calculate: a. the rate of flow for each pipe, b. the diameter d of a single pipe 100 m long which would give the same flow if it was substituted for the original two pipes, (Notes: Use Darcy Weisbach's equation, h,= (flv²)/(2dg) Pipe 2- Pipe 1 h = 10 m 110
SUBJECT: HYDRAULICS FINALS ANSWERS MUST BE 3 DECIMALS AND BOX IT SHOW COMPLETE SOLUTION BADLY NEED IT ASAP EXPERTS. THANK YOU
If the water surface elevation in reservoir B is 110 m, what must be the water surface elevation in reservoir A if a flow of 0.03 m^3/s is to occur in the cast iron pipe. Use f= 0.0021 for all pipes. Include minor losses. (DO NOT ROUND OFF)
Three reservoirs A, B and C are connected by a pipe system shown in the figure below. If the rate of flow from the reservoir A is 55 l's, and the coefficient of friction (F) for all pipes is 0.015. Find the piezometric head at point D A L2=600 m d2=20 cm D Q1=0.055 m/s L1=1200 m d1=30 cm 28 m 30 m
Determine the elevation difference, Ah, between the water levels in the two open tanks shown in the figure below. Assume SG = 0.92. Δη= m 1m SG. Water 0.4 m ↑ Ah
A conduit is carrying oil ( S = 0.75 ) and its absolute viscosity is 0.25 kg / m-s. If the flow rate is 0.45 cu.m/s Determine the following • The entrance length • The length of the inviscid cone • The length of the profile development given the following situations 1. Circular pipe 800mm 2. rectangular pipe (Width = 800mm, Depth 1200mm)
Two reservoirs are connected by two pipes in series,as shown below. Determine the flow rate using ken = 0.55 and kex= 1.8. Use the explicit form of the Colebrook-White equationdeveloped by Moody to solve for the friction factors. Let μ =1.003x10-3 kg/m-s
Please aid me with this, i will also need to learn how to do this.
Current Attempt in Progress Determine the elevation difference, Ah, between the water levels in the two open tanks shown in the figure below. Assume SG = 0.83. Ah = m 1 m SG Water 0.4 m Ah