The three-part axially loaded member in Figure bellow consists of a tubular segment (1) with outer diameter-37.5 mm and inner diameter = 22 mm, a solid circular rod segment (2) with diameter 37.5 mm, and another solid circular rod segment (3) with diameter 22 mm. The line of action of each of the three applied loads is along the centroidal axis of the member. Determine the axial stresses o,, 02, and o, in each of the three respective segments. Note: All segments with circular cross section. 37.5mm 22mm (1) (2) (3) EENEEN 22mm 9KN As free body diagram : (1) 37.5mm (2) (3) 22mm 9KN F1 14KN 18KN 22mm

The three-part axially loaded member in Figure bellow consists of a tubular segment (1) with outer diameter-37.5 mm and inner diameter = 22 mm, a solid circular rod segment (2) with diameter 37.5 mm, and another solid circular rod segment (3) with diameter 22 mm. The line of action of each of the three applied loads is along the centroidal axis of the member. Determine the axial stresses o,, 02, and o, in each of the three respective segments. Note: All segments with circular cross section. 37.5mm 22mm (1) (2) (3) EENEEN 22mm 9KN As free body diagram : (1) 37.5mm (2) (3) 22mm 9KN F1 14KN 18KN 22mm

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.4.21P: -18 through 7.4-25 An clement in plane stress is subjected to stresses a,, ay., and axy. (see...

See similar textbooks

Similar questions

A solid aluminum bar (G = 27 GPa ) of diameter d = 40 mm is subjected to torques T = 300 N - m acting in the directions shown in the figure, Determine the maximum shear, tensile, and compressive stresses in the bar and show these stresses on sketches of properly oriented stress elements. Determine the corresponding maximum strains (shear, tensile, and compressive) in the bar and show these strains on sketches of the deformed elements.
-26 A rectangular plate of dimensions 125 mm × 75 mm is subjected to tensile stress sy= 67 kPa and compressive stress a. If it is known that the normal stress along the diagonal t—t is ??t= -6.57 kPa, find stress ??y on element A. a
A plane frame with a pin support at A and roller supports at C and £ has a cable attached at E. which runs over Frictionless pulleys al D and B (see figure). The cable force is known to be 400 N. There is a pin connection just Lo the left of joint C. (a) Find reactions at supports^, C, and E. (b) Find internal stress, resultants N, V, and M just to the right of joint C. (c) Find resultant force in the pin near C.
-18 through 7.4-25 An clement in plane stress is subjected to stresses ax,ay., and txy. (see figure). Using Mohr’s circle, determine (a) the principal stresses and (b) the maximum shear stresses and associated normal stresses. Show all results on sketches of properly oriented elements. 7.4-18 sx= 2900 kPa, sy= 9100 kPar,txy=-3750kPa
A single steel strut AB with a diameter (a) Find the strut force Fs and average normal stress ds= 8 mm supports the vehicle engine hood of a in the strut. mass 20 kg that pivots about hinges at C and D (see (b) Find the average shear stress t aver in the bolt at A,figure parts a and b). The strut is bent into a loop at (C) Find the average bearing stress bon the bolt at A. its end and then attached to a bolt at A with a diameter db= 10 mm. Strut AB lies in a vertical plane.
through 7.4-25 An clement in plane stress is subjected to stresses sx,??y,and txy. (see figure). Using Mohr’s circle, determine (a) the principal stresses and (b) the maximum shear stresses and associated normal stresses. Show all results on sketches of properly oriented elements.
Solve the preceding problem if F =90 mm, F = 42 kN, and t = 40°MPa
The stresses acting on element A on the web of a train rail (sec figure part a) a re found to be 6500 psi tension in the horizontal direction and 18,500 psi compression in the vertical direction (see figure part b), Also, shear stresses with a magnitude of 3800 psi act in the directions shown. Determine the stresses acting on an clement oriented at a counterclockwise angle of 30° from the horizontal Show these stresses on a sketch of an element oriented at this angle
-18 through 7.4-25 An clement in plane stress is subjected to stresses a,, ay., and axy. (see figure). Using Mohr’s circle, determine (a) the principal stresses and (b) the maximum shear stresses and associated normal stresses. Show all results on sketches of properly oriented elements.
Solve the preceding problem for an element in plane stress on the bottom surface of a fuel tanker (figure part a); stresses are sx= 105 MPa, sy. = 75 MPa, and ??xy= 25 MPa. Determine the stresses acting on an element oriented at an angle ?? = 40° from the x axis, where the angle is positive when counterclockwise. Show these stresses on a sketch of an element oriented at the angle ??.
An element on the top surface of the fuel tanker in Problem 7.2-1 is in biaxial .is in the and is subjected to stresses a, = 6250 psi and a. = -1750 psi, as shown in the figure. Using Mohr s circle, determine the following: (a) The stresses acting on an element oriented at a counterclockwise angle ? = 550 from the x axis. (b) The maximum shear stresses and associated norm al stresses. Show all results on sketches of properly oriented elements.
,3-23 A 200-lb trap door (AD) is supported by a strut (BC) which is pin connected to the door at B (see figure). (a) Find reactions at supports A and C. (b) Find internal stress resultants N, V, and M on the trap door at 20 in. from A.