The thin-walled tube is subjected to an axial force of 40 kN. If the tube elongates 4 mm and its circumference decreases 0.09 mm, determine the modulus of elasticity, Poisson's ratio, and the shear modulus of the tube's material. The material behaves elastically. 40 kN 900 mm 10 mm 40 kN 12.5 mm

Q: 3 MPa. Which of the following describes the stress state? A body is subjected to the following…

A: in question stress in various plane is given:  question is asking about stress state: given: SIGMAxx…

Q: A straight wire 15 m long is subjected to tensile stress of 2000 kgf/cm². Elastic modulus is 1.5x106…

A: We have to calculate the temperature change to produce the same elongation

Q: A strain gage is installed in the longitudinaldirection on the surface of an aluminum beveragecan…

A: Given data:- The radius-to-thickness ratio of the Can is, R= rt=200 The strain changes, ∈0=187×10-6

Q: A brass wire of diameter d = 2.33 mm is stretched tightly between rigid supports so that the tensile…

A: (a) What is the maximum permissible temperature drop (in °C) if the allowable shear stress in the…

Q: At an axial load of 25 kN, a 45-mm-wide by 20-mm-thick polyimide polymer bar elongates 2.9 mm while…

A: Axial load (P) = 25 KN = 25 × 103 N Elongation in bar (∆L) = 2.9 mm Change in width (∆b) = 0.19 mm…

Q: A specimen is originally 300mm long and has a diemter of 11mm and it subjected to a force of 4kN.…

A:

Q: A rubber ball is inflated to a pressure of 65 kPa. At that pressure, the diameter of the ball is 240…

A:

Q: A solid bar with dimensions Lxwxw is stretched along its length by 8%. During the deformation the…

A: Given Stretch in longitudinal direction 8%  Change in volume 0

Q: For a given material if the Young's modulus is 200 GN/m² and odulus of rigidity is 80 GN/m?, then…

A: Given data : Youngs modulus (E)=200  GN/m2Modulus of rigidity (G)=80  GN/m2

Q: The flow stress (in MPa) of a material is given by 500 e0.1 , Where e is true strain. The Young's…

A: given- flow stress-σ=500ε0.1young modulus E=200 GPathickness=100 mmcompressed to 95 mm

Q: The slope of the stress-strain curve in the elastic deformation region is

A: The given question asked here is the slope of the stress-strain curve in the elastic deformation…

Q: The material of a rubber balloon has a Poisson's ratio of 0.5. If uniform pressure is applied to…

A: Given Data; Poisson's Ratio = (μ)  = 0.5 Uniform pressure applied to blow to balloon. To Determine…

Q: At an axial load of 22 kN, a 15-mm-thick x 35- mm-wide polyimide polymer bar elongates 4.6 mm while…

A: Given,  L = 315 mm B = 35 mm Thickness = 15 mm Load = 22 kN Length elongation = 4.6 mm With…

Q: At an axial load of 24 kN, a 50-mm-wide by 20-mm-thick polyimide polymer bar elongates 3.1 mm while…

A: Given, Axial load, P = 24 kN or 24000 N Cross section size = 50mm x 20mm Length = 210 mm

Q: Q- Principal stress at a point in an elastic material are 1.5 o (tensile), o (tensile) and 0.5o…

A: Given- Principal stress- σ1=+1.5σ σ2=+σ σ3=-0.5σ  Elastic limit E=210 MPa, Poisson's ratio- μ=0.3,…

Q: A wire of circular cross-section of diameter 1.0 mm is bent into a circular arc of radius 1.0 m by…

A: Given- Diameter d=1 mm, Radius of arc R=1 m, E=100 GPa, It is needed to find the value of the…

Q: A homogenous isotropic material of size 20 cm x 20 cm x 20 cm is placed inside a rigid box of…

A: Consider the free body diagram;Given;Young modulus, E=Poisson ratio, v=0.3

Q: An assembly of a material consists of a brass shell fully bonded to a ceramic core. The brass shell…

A: Given Data:Outside dia of brass shell=75mmInside dia of brass shell = 45mmTemperature =…

Q: = 30 mm. When Before loading on the cylindrical brass rod, its length is Lo = 0.3 m and its radius…

A: NOTE - Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the…

Q: A body is subjected to stresses as shown in the figure given below. 90 MPa 35 MPa 145 MPa The FOS as…

A:

Q: Two strain gages are mounted on a thin-walled cylindrical pressure vessel. One strain gage is…

A: It required to find Longitudinal stress Hoop stress Gage pressure

Q: b) Figure Q1 shows ceramic specimens subjected to the pure uniaxial force. Specimen A is compressed…

A: An elemental area can be subjected to stress due to applied load . For uniaxial it is subjected to…

Q: The interconnected bars were pulled 15.71 mm from the right end and fixed. Bar 1 has a length of 4…

A: The given figure is shown below:

Q: A tensile test is conducted on a bar whose cross-section is 12mm thick by 100mm wide. An axial…

A:

Q: A homogenous isotropic material of size 20 cm x 20 cm x 20 cm is placed inside a rigid box of…

A:

Q: The rigid horizontal slab is attached to two identical copper rods. There is a gap Δ = 6.18 mm…

A: Finding change in length and stress induced due to temperature rise

Q: Theory of Failure Question 1: The uniaxial yield stress of a material is 866 MPa. According to von…

A: Yield stress- σy=866  MPa, It is needed to find the shear yield stress as per the Von-mises…

Q: 2) For a specific material having poisson's ratio -0.32, the percent of elastic modulus to modulus…

A:

Q: At an axial load of 25 kN, a 50-mm-wide by 15-mm-thick polyimide polymer bar elongates 3.1 mm while…

A: Given that :-Required that :-(a) Modulus of elasticity (E) =?(b) Poisson ratio (v) =?(c) The change…

Q: A wire of circular cross section is wound around a drum of 500 mm diameter. Ewire 100 GPa. If the…

A:

Q: 1: For a material stress at proportionality limit is 400 MPa and modulus of elasticity is 200 MPa.…

A:

Q: A 20 m long steel rod is at a temperature of 20°C. The rod is heated so that temperature rises by…

A: Given data- 20 m long steel rod at temperature = 20oC Temperature rises to 50oC Rod can expand upto…

Q: len A material has the stress-strain behavior shown in the Figure below. Calculate the toughness (T)…

A:

Q: At the limit of proportionality, a bar 30 mm wide (w) and 12 mm thick (t) elongates 2.0 mm under an…

A:

Q: Question: Principal stresses at a point are 80 N/mm² and 40 N/mm2 both tensile. The yield stress in…

A: Given- Principal stresses- σ1=80 N/mm2,σ2=40 N/mm2, Yield stress- σy=200 N/mm2, It is needed to find…

Q: True stress-strain behaviour of a metal is given by the flow curve equation o = 1750 €0.37 where o…

A:

Q: A circular rod and a 3/8-in.-thick rectangular bar are both made of a plastic material that has an…

A:

Q: In a steel railroad, the 12 meters long rails are laid with a clearance of 5 mm at a temperature of…

A: solution the length of steel rod L =12mts clearance gap ∆=5mmE=200Gpa=200×1000 Mpa a for linear…

Dependence on mechanical properties

The mechanical properties of materials are those structures that include the reaction to the load used. Metal switching features determine the scope of the usefulness of the content and establish the expected service life. Machine structures are also used to help distinguish and identify material objects. The most common mechanical properties considered are strength, ductility, stiffness, impact resistance, and resilience to fractures.