Solve it correctly please. I will rate accordingly. The tension in the cable AB is 150N. Thecoordinate, dimensions of the hatch and po-sition of point A are described as in the fig-ure.A (0.4,0.3,0) m• Determine the moment about the r-axis due to the force exerted on thehatch by the cable at point B• Draw a sketch to indicate the directionof the moment0.6 mB1.0 m

Answered: Image /qna-images/answer/3bf89f6a-9f6b-431c-be83-549a0df37385.jpg

Answered: The tension in the cable AB is 150N.…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Bevel Gear A pair of bevel gears connects shafts at right angle with speed ratio of 2:3. The larger gear has 30 teeth with 4-tooth per inch diametral pitch. The gear is made up of 20°involute full depth. Determine the following: a) the number of teeth of pinion b) the pitch angle of gear c) the pitch angle of pinion d) the pinion diameter e) the gear diameter f) the length of cone g) the expected value of addendum h) the expected value of addendum angle i) the face angle of pinion j) the face angle of gear k) the dedendum l) the dedendum angle m) the cutting angle of pinion n) the cutting angle of gear.
Solve the following problems and SHOW YOUR COMPLETE SOLUTIONS FOR BETTER UNDERSTANDING
Imagine two ordinary gears of different diameters meshed together, with the larger being the driver. If the larger gear has 108 teeth around its circumference and rotates at 5.80 rad/s, the smaller gear, which has only 20 teeth, will rotate at what speed?
calculate the indexing for the following: 1. 914 divisions 2.1300 divisions note: the link for the calculations is provided https://www.youtube.com/watch?v=Z0FR4gzPHiU
q12 Complete the answer
Please solve it correctly , Don't Use Ai tool. (1) A twist drill bit is used to drill a hole of diameter 2.0 at 4578.1 rpm at a feed rate of 2.5 in/min. Calculate the MRR in in^3/min. Take "pi" = 3.14. Round your answer to the nearest tenth.
Two gears mounted on shafts have 10 and 15 teeth, respectively. The center distance is 10 inches. The addendum equals the module, and the clearance equals 0.135 times the module. Determine (a) pitch diameters, (b) addendum, (c) dedendum, and (d) root circles. Draw simple circles showing the diameters and the center distance. Complete solution and drawing is required.
A helical gear of 10 inches pitch diameter has a helix angle of 25 degree, and there are 35 teeth. The gear transmits 40 hp and rotates at 450 rpm with a normal pressure angle of 20 degrees. Find the axial force transmitted by the gear. A 252.26 lb B 225.26 lb C 522.26 lb D) 552.26 lb
The spur gearing arrangement made of two parallel shafts,whose pitch circle diameters of driven and driver gears are 84cm and 35cm respectively. If driven shaft runs with 10 r.p.s,determine the following; 1. Center distance between the two shafts in mm. 2. Speed of driver shaft in rpm 3. Velocity ratio 4. Number of teeth's on driver and driven shaft for the given module 6mm
I need the answer quickly
MECHANICAL ENGINEERING UPVOTE WILL BE GIVEN. PLEASE WRITE THE COMPLETE SOLUTIONS LEGIBLY. SHOW THE STEP-BY-STEP PROCESS WITH SHORT COMMENT/EXPLANATION. ANSWER IN 4 DECIMAL PLACES. Determine the torque (in N-m) applied to the shaft of a car that transmits 450 hp and rotates at a rate of 3000 rpm.
A motor is driving an output shaft through a single-stage gears, as shown. Input Gear, N, Motor To Output Gear, N2 Number of teeth of the input gear, N1 = 24; Number of teeth of the output gear, N2 = 48; Gear efficiency = 95%; %3! If the output shaft is to deliver torque To = 20 Nm, calculate the torque required on the input shaft, Ti. Give your answer in Nm to 1 decimal places.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

The tension in the cable AB is 150N. The coordinate, dimensions of the hatch and po- sition of point A are described as in the fig- ure. • Determine the moment about the r- axis due to the force exerted on the