The system, which is initially stationary, started to move with m, and m3 weights as shown in the figure below. Since, m, = 5g, m2 = 10g, m3 = 25g, how much will m2 be displaced after 4 seconds? (Assume that the surfaces and joints are frictionless, the paths are long enough, g = 9.8 m/s².) m2 m1 m3

The system, which is initially stationary, started to move with m, and m3 weights as shown in the figure below. Since, m, = 5g, m2 = 10g, m3 = 25g, how much will m2 be displaced after 4 seconds? (Assume that the surfaces and joints are frictionless, the paths are long enough, g = 9.8 m/s².) m2 m1 m3

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

Steel ball with radius of 0.13 m lays on a bottom of the lake 6 m deep. What work is needed to lift the ball to the surface of the lake? Density of steel is 7860kg/m3. The volume of a sphere is Use g = 9.8 m/s2 Calculate answer to two decimals.
@ 108 W K F 25,551 A 3 E D 80 7 C 6. A 90.0-kg circus performer jumps from a height 5.30 m onto a trampoline and it stretches 0.35 m. Assume that the trampoline obeys Hooke's Law. How far will it stretch if the performer jumps from a height 8.0 m? ADE and Santi 2010ning $ MAR 2 22 R 888 FA F V % 5 FS T G m 6 tv B MacBook Air F Y H & 7 34 F7 U N ** 8 J Dil 66 1 3 ( 9 A K DD FO MOSISO O W F10 P P zoom command e FM - EA vawes or roe puffer 12 2 ISUH H by mi 04 M option
Three equal spheres (A, B, C) have loads of values indicated in the figure and isolated from the floor. Sphere A is placed in contact with Sphere C and separated. Then, sphere A is brought into contact with sphere B and separated. At the end, sphere B is placed in contact with sphere C and separated. What are the loads of A, B, C at the end of the process? Justify with text, diagrams or calculation
phy
A scale stretches 7 cm for a 7 kg load. How far apart are the 0.5 kg marks on it to the nearest mm?
WORK 1. The blocks A and B are connected by a cable that runs around two pulleys of negligible mass, as shown in the figure. The kinetic coefficient of friction between the inclined plane and block A is 0.4. If the initial velocity of A is 3m/s down the plane, determine the displacement AS, of block A (measured from its initial position) when the system comes to 8 m/s A 5 kg Hi = 0,4 rest. | 20° 3 kg
A block of weight W is dropped from height H onto a spring that has a spring constant of k as shown in the figure. Which expression gives the correct answer for the maximum compression x of the spring from the equilibrium? 37-
30⁰ Given: Using the provided information, compete the following problems. NOTE: Find: The system shown is initially in static equilibrium and motionless. Submitted responses shall be to 4 significant figures. Do NOT use scientific notation. 1. The maximum magnitude of the Weight-W that will not initiate motion is 2. The minimum magnitude of the Weight-W that will not initiate motion is 3. Assume the 50LB-Block is on the verge of moving up the inclined plane. The magnitude of internal force in the rope (near the 50LB-Block) is 4. Assume the 50LB-Block is on the verge of moving down the inclined plane. The magnitude of internal force in the rope (near the 50LB-Block) is 50 lb Hs=0.30 W H, = 0.20 LB. LB. LB. LB.
5. (A5-1) A water tank has the shape of an inverted square pyramid with a height of 15 m and a base side length of 21 m. It is currently filled with water to a height of 10 m, which as a density of 1000 kg/m³. Find the amount of work required to empty the tank by pumping all of the water to the top of the tank.
I need the answer as soon as possible
General Physics 1 Mod 5 no. 16
In a 30°-rough incline, a 1.25 kg block is initially at rest beside a spring that is compressed by 24 cm as shown in the figure below. The spring has a spring constant of 180 N/m and the coefficient of sliding friction between the incline and the block is 0.23. When the spring is released, how far up the incline (with respect to its initial position) will the block slide before sliding back? ww 30⁰