The system shown starts from rest. Determine the velocity of the crate when it has moved 1 m. 45 kg 20⁰ 0.15 m μ=0.4 M = 50 Nm A IA = 4 kgm²

Q: Aşağıda verilen yapıda BC yapı elemaninın uzerindeki y 0.9 m 0.75 m 1.8 m 2.5 kN

A:

Q: d AB (G= 39 GPa). Eac

A: answer= 17.899 deg

Q: Q1 -B- Draw just the Free Body Diagram of the following figures. 30 kN/m Fig. (2) -3 m- +-3m- -3m-…

A: given; draw free body diagram for given figure;

Q: 5. Determine the strength of a % in bolt having a yield stress of 60 ksi and stress area of 0.1134…

A:

Q: Consider the cable system shown in FIGURE P3-18 of the textbook. If: • e - 45° then, what is the…

A:

Q: Determine the support the actions 36.5 kN/m 6m 36.5 kN/m 1 3m ( 4.6m

A: Determine the support reactions

Q: A fluid flows over a flat plate at a velocity of 26 `m/s as shown in the figure. The length in…

A:

Q: - 750 mm G. D 225 mm F 900 mm E 1200 mm-

A: Find the reactions at each joint and force in rope.

Q: What are the V and M diagrams? Thanks! 50 kN 125 kN 50 kN B C D A E -0.5 m 0.3 m 0.4 m 0.2 m

A: As per the guidelines of BARTLEBY we are subjected to solve only one question at a time. Please…

Q: Q- 6- Resolve the force 250N into rectangular components 250 N 16 9. 12

A: Here, Magnitude of the force = 250 N   For the given triangle, missing angle θ can be found by,…

Q: 200 400 A 200 N m 200 - F Dimensions in mm Determine the magnitude of the force (in N) of the x-…

A:

Q: Specify its location, measured from point A. Express your answer with the appropriate units. z = μÀ…

A: Given data: distributed load, w = w(x)  = (-2x2+4x+16) lb/ft.   To calculate: A. Magnitude of the…

Q: Determine the smallest coefficient of static friction at both A and B needed to hold the uniform…

A:

Q: shown The distributed load acts on the shaft as shown. Suppose that a = 0.7 ft. (Figure 1) Figure…

A:

Q: 2. Determine Ig-g for the T-section shown. | 40mm 209.545mm 250 mm g 100.455mm 60 mm 200 mm

A:

Q: For the wood beam shown in Figure A, assume L = 1.5 mand P = 15 kN. The beam cross section shown in…

A:

Q: Required information Problem 03.090-Multiple forces are applied to a plate NOTE: This is a multi…

A:

Q: The vertical force T = 121 kN is applied to the frame. Given: L1= 38.9 m; L2 = 5.7 m; L3 = 4.2 m.…

A:

Q: Replace the loading on the frame by a single resultant force. Suppose that F = 700 N, a = 0.5 m, and…

A: GivenF=700Na=0.5mh=1.3m

Q: Q3 Derive the relations 2²F' Cy = -T ƏT? and Cp 3 —Т ƏT² P

A:

Q: O find the root of the oquation -37/2 2t e . tant (3)

A: According t the question, f(t)=e2t. tant-e-3π2on differntiating this equation with respect to…

Q: find the tensile of the bolt with diameter 38mm,80kN

A:

Q: Write the matrix equations in terms of stress tensors for the three equations

A: consider three mutual perpendicular normal stresses σxx , σyy , σzz acts at a component along x, y…

Q: A cross-section of a beam is shown in Figure Q2. If the shear force in this section is V = 125 KN,…

A: Given : The shear force in this section is The diagram is,

Q: Remake the diagram for this problem. Empasize the area of 1,2,3, 4 and refer to the solution. No…

A:

Q: a. Use Mohr's Circle to determine the maximum shear stress on the element b. Also, using Mohr's…

A: Mohr's circle for, σx=-30MPaσy= 50MPaτxy= 20MPa

Q: How is the stress at a point determined?

A: Solution:

Q: find the magnitude of T and its direction (0) for which the eye bolt under a resultnea donnid of…

A:

Q: Problem 3. What is the moment of the 1.4 kN force along the direction of the 1.0 kN force? Express…

A: All the dimensions are shown in the figure.For finding the moment of the 1.4 KN along the 1 KN axis,…

Q: L,=40mm; L,= 120mm; L,=80mm L=100mm and 0,=65°. Find the possible value of 0, and and 0,

A:

Q: Question 4 Part A If 0 = 27° and F = 5 kN , determine the magnitude of the resultant force acting on…

A: Given -

Q: What is the Share Force (in KN) at a point 0.6L (where L is the length of the plank) given that: F1…

A:

Q: What steps should be taken to obtain The resultant internal loadings at a point located on the…

A: The internal loading are the forces and the moments that are applied by the half of the section on…

Q: The assembly supports a uniform distributed load = 1.65 kN/m as shown. Part A Determine the…

A:

Q: The internal loadings at a cross section through the 120-mm-diameter drive shaft of a turbine…

A:

Q: 3.6 m R 1m 1.2 m 2.5 m 3m The banner has a density of 670 kg/m and is 6mm-thick. The pipe has the…

A:

Q: 3. Determine the normal force, shear force, and moment at a section thre ugh point C.Take B 0.1' m…

A:

Q: Which of the following statements is/are true? 1. The force per unit area, or intensity of the…

A: Stress is defined as the ratio of force applied to the body to the cross sectional area of the…

Buckling of columns

The column is described as a vertical member of the structure that carries an axial compressive load, and buckling is a lateral deformation of the column under the application of load.