The system shown in the figure is used to accurately measure the pressure changes when the pressure isincreased by Ap in the water pipe. When Ah = 70mm, what is the change in the pipe pressure (in Pa)?WaterPipeGlycerin, SG = 1.26D=30 mmAhd = 3 mm

Given data:∆h=70 mmSpecific gravity of glycerin=1.26Pipe diameter, d=3 mmD=30 mm

The system shown in the figure is used to accurately measure the pressure changes when the pressure is 70mm, what is the change in the pipe pressure (in Pa)? increased by Ap in the water pipe. When Ah Water Pipe Glycerin, SG = 1.26 D=30 mm Ah d=3mm

The system shown in the figure is used to accurately measure the pressure changes when the pressure is 70mm, what is the change in the pipe pressure (in Pa)? increased by Ap in the water pipe. When Ah Water Pipe Glycerin, SG = 1.26 D=30 mm Ah d=3mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A docs.google.com/forms/d/e/1FAlpQLSetk8UE/ PROBLEM 6: A gasoline line is connected to a pressure gage through a double-U manometer, as shown. If the reading of the pressure gage is 260 kPa, determine the gage pressure of the gasoline line. Assume the density of air to be 1.225 kg/m3 * Oil SG = 0.79 P gage = 260 kPa Gasoline SG= 0.70 Pipe Air 45 cm 50 cm 22 cm 10 cm Mercury SG= 13.6 Water Your answer
A gasoline line is connected to a pressure gage through a double-U manometer, as shown. If the reading of the pressure gage is 40 psi, determine the gage pressure of the gasoline line. Assume the unit weight of air to be 0.0765 lb/ft3. pls answer asap thank you
28. The tank shown in figure below is closed at top and contains air at a pressure at top and contains air at a pressure of P. The value of Pfor the manometer readings shown will be X- Open tube 200 cm 10 cm T © Air - X 4 A Oil RD = 0.75 Water T 150 cm
Consider oil flowing through a horizontal pipe at a rate of 3 liter/s. There are two sections of the pipe with diameters 10 cm and 7 cm and the two sections are connected by a smooth reducing section as shown in the schematic. We use a manometer with glycerin as the manometer fluid (with glycerin density of Pglycerin 1,260 kg/m³) to measure the pressure difference between the two pipe sections. Assume that frictional effects are negligible and consider specific gravity of oil as SGoil = 0.76. What is the manometer reading, h (i.e. differential height of glycerin between the two arms of the manometer)? 10 cm I h T 7 cm-
10
Problem 3.25 The acrylic plastic rod is 200 mm long and 25 mm in diameter. Figure 1 of 1 -200 mm- Part A If an axial load P of 400 N is applied to it, determine the change in its length. Ep =2.70 GPa, vp = 0.4. (Figure 1) Express your answer with the appropriate units. 8 = Submit Part B μÃ Ad= Value Submit Incorrect; Try Again; 4 attempts remaining Units My Answers Give Up Determine the change in its diameter. Express your answer with the appropriate units. μA Value Units ? My Answers Give Up ?
Read the question carefully and give me right solutions with clear calculations
USE ALL DECIMAL PLACES IN SOLUTIONS AND ROUND OFF YOUR ANSWERS TO NEAREST WHOLE NUMBER. INPUT NUMERICAL VALUE ONLY.
IV. Water is discharged from a device in to air, as shown in the figure. How much is the horizontal force to hold the device. Ignore gravity and viscosity. 1 Ibf= 1 slug ft/s 2, air (2)A=0.4 t 30 fU 10 psi Flang 1/20 tis (1) A=0.8 (E) A- 0.8 n air Water density =1.94 slugs/ft^3.
Q/ The laminar flow of water through a pipe is measured by means of a pitot tube situated in the center of the pipe; the reading of a mercury manometer connected to the pitot is 100 mm. The flow is also measured by a venturi meter which connected with the same mercury manometer and the pressure drop across it equals to 300 mm. Find the ratio of venturi to pipe diameter and determine the pressure drop due to friction across the venturi meter.
Solve for the Absolute Viscosity and the Kinematic Viscosity using the given below.
A manometer consists of a tube of 0.5 inch in the inner diameter and an amount of mercury (SG Hg =13.55). On one side of the tube, oil (SG=1.4) was trapped, a bubble formed, and the fluid inside was stationary. The volume of the oil was 0.6 in^3 and the volume of the air was 0.2 in^3. Now, the oil and bubble are removed. The pressure change across the air bubble is negligible and any curvature on the bubble surface can be neglected in calculating the volumes. Determine how much the mercury height rises (i.e. h 4 -h 2 ).