The system in the figure is in balance. A load of 1600 kg is suspended from point C on the cable connected from points A and B. The relevant distances are clearly given in the figure. In this case, calculate the forces in the AC and BC cables. 24- Force on AC cable? (kg) 25- Force, BC in cable? (kg)

The system in the figure is in balance. A load of 1600 kg is suspended from point C on the cable connected from points A and B. The relevant distances are clearly given in the figure. In this case, calculate the forces in the AC and BC cables. 24- Force on AC cable? (kg) 25- Force, BC in cable? (kg)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Hello, please answer as soon as possible. Choose from the given choices/options below the question. Show complete solution if necessary. Thank you for your help. I’ll rate you with like/upvote.
Q3. In the figure below, one end of the uniform beam of mass 50 kg is hinged to a wall. The other end of the beam is supported by a cable that makes angles e = 30 degrees with both the wall and the beam. A box of mass 10 kg is hanged at the end of the beam with a rope. The magnitude of the forces at the hinge. Hinge rope Mg=10kg cable -.
Two cables are used to hang a traffic light as shown in Figure 1(b). The weight of the traffic light is 1000 N. If the traffic light is in equilibrium position, determine the magnitude of the force F and its direction. 600 N y 30⁰ F Figure 1 (b): Traffic light
The turnbuckle shown in Figure has a square thread with a mean radius of 5 mm and a lead of 2 mm. If the coefficient of static friction between the screw and the turnbuckle is 0.25, determine the moment M that must be applied to draw the end screws closer together. Choices: A. 6.36 N-m B. 7.36 N-m
The hoisting arrangement for lifting a large pipe is shown in the figure SD-05Q002. The spreader is a steel tubular section with outer diameter 75 mm and inner diameter 60 mm. Its length is 2.5 m and its modulus of elasticity is 200 GPa. What is the maximum weight of pipe, in kN, that can be lifted based on the following conditions? (Assume pinned conditions at the ends of the spreader.) Use: V = 3 H = 4 Problem 7 Based upon a factor of safety of 2.0 with respect to Euler buckling of the spreader. a. 205 b. 434 c. 355 d. 217 Problem 8 Based upon the allowable stress design if Fy = 248 MPa. a. 205 b. 434 c. 355 d. 217 Problem 9 Based upon the critical stress. a. 205 b. 434 c. 355 d. 217
Advanced structural engineering
Two cables are used to hang a traffic light as shown in Figure 1(b). The weight of the traffic light is 1000 N. If the traffic light is in equilibrium position, determine the magnitude of the force F and its direction. 600 N y 30⁰ F Figure 1 (b): Traffic light
The (force) demands from shear wall and floor elements are given per unit foot. For example, moment and shear demands are given in 20,000 lbf-ft/ft and 3000 lbf/ft for a shear wall element. Which of the following CORRECTLY describes a design process using the analysis outcome. Select ALL that apply. In the example, the shear demand of a 12-inch wide column (or a strip of the wall) is 3000 lbf. In general, moment demand per unit width (1 ft) should be used for a concrete floor element design. In the example, the moment demand of a 1-ft wide column (or a strip of the wall) is 20,000 lbf-ft. In general, shear force demand per unit width (1 ft) should be used for design (of both concrete floor and wall elements).