The switch in Fig. has heen in position A for a long time. Att = 0, the switch moves to B. Determine v(t) for t>0. 3 k2 B 4 k2 ww- t = 0 24 V 5 kn 0.5 mF 30 V

Q: What is the voltage drop across RC, VC, in volts?  (Enter the number, not the units.)

A: Given circuit is -

Q: Explain in clearly the difference between Intensive and Extensive readings.

A: Given Enumerate the differences between intensive and extensive reading. Please find the below…

Q: difference between measurement uncertanty and measurement error

A: Given : Need to find the difference between measurement error and uncertainty.

Q: Is Mc microfarads?

A: Given, The abbreviation of mc =?

Q: 40% of the production in a factory is I. Makina, 35% II. Machine and 25% III. Machine It is produced…

A: The question is from the Bayes theorem and as per Bayes theorem if A1 ,A2 ,A3 ......An be a…

Q: In an electronic circuit, a. current remains the same through all the series components. b. voltage…

A: Note that,  In an electronic circuit, current remains same jn all series components and voltage…

Q: Khee Voltage of Ilicon semi nductor. (without Your answer A condition where zero (0) volt is less…

A: 1) Knee voltage of silicon semiconductor is 0.7

Q: What is sub station

A: A power station is to provide electricity to a huge number of people. Different customer’s power…

Q: In FET, what is the value for when Ip=lpss/2? [Approximate time to answer: 2 Minutes.] O gmo/2 O 3…

A: solve for transconductance

Q: Test 2: Modified true or false:Shade letter A if the first statement is True, Shade Letter B if the…

A: The given statements are as follows, 1. The passing general average rating shall be seventy percent…

Q: Given the information appearing in Figure beside (assume Ic=IE) determine: (a) Ic. (b) VE. 18 V (c)…

A: Disclaimer:  Since you have asked multipart questions, we will solve the first three subpart for…

Q: What is HT supply?

A: What is HT supply?

Q: Difference in the digital and the analog systems

A: Both digital and the analog systems are used to transmit and received information (or signals). The…

Q: IEEE and IEC standards

A: standards for electrical safetyIEC - international electrotechnical commissionIEEE - institute of…

Q: Label the parts of Tubular Steel Poles

A: Steel tabular poles are not commonly used poles these poles are used when there is need of low cost…

Q: A transistor is used as a switch and the waveforms are shown below. The parameters are given as…

A: Given  Transistor as switch and waveforms as shown  Vcc=200 vVCE(sat)=1 vICS=100 AICEO=1 mArise time…

Q: Briefly describe how a distance can be measured by the method of phase comparison

A: From the method of phase comparison, the distance is measured indirectly by determining the number…

Q: Define Analog

A: Analog can be defined as the signal, which is continuous. The analog signal has a time-varying…

Q: The neutral current is equal to three times of ....... sequence current.

A: Current in nautral is sum of three phase currents. Current in each phase is sum of possitive…

Q: Write a paragraph about your hopes and ambitions. In about 100 words

A: Hope and ambitions are the most important part of any human which can include the happiness of…

Q: 19. Identify the response time of a meter. a. Time taken by output to reach final constant value…

A: Identify the response time of a meter. It's depend on the parameter.

Q: In FET, An outward-pointing arrow represents ___. Choose the correct answer below: a.N-type…

A:

Q: 3) What is the dropout ratio? What is the advantages of dropout ratio in power systems. (min 1 page)

A: A pick-up and drop-out ratio terms related to protective relays. The pickup current of a circuit…

Q: Solve for VCE +13 V 4.5 kQ 1 ko 30 uF 10 uF Vo B = 69 10.5 1.5 ka 50 uF ww ww

A:

Q: The circuit shown in Figure Q5.1 consists of a current source connected to a load via a cable. The…

A: Given circuit is - Value of current source is -

Q: Explain the Difference between the Fundamental and Derived Unit.

A: There are generally  three types of units which are used to typically measure a particular physical…

Q: Explain with a neat block diagram the measurement of temperature using RTD

A: On the principle of metal resistance increasing with temperature we use a device which is Resistance…

Q: 9Vpk pk Vin Vout 1.25 2.25 3.75 4.50 -1.25 -2.25 -3.75 -4.50

A: We need to find out output voltage for given input values in clamper circuit .

Q: in zeq 1 where did you get 210.949 from?

A: Student is asked to explain from where did get ZB 210.949 from?

Q: Give the concise definition or process of getting the equations in each loop/mess (Mesh Analysis) in…

A: Let us try to understand the concept of mesh analysis in this answer.

Q: Question 4 What do you do to an asynchronous counter to let it count from 1 to 13? (Handwriting…

A: The solution is given below

Q: 1. Explain the elements of measurement system in detail.

A: According to the given question, it is required to explain the elements of measurement system in…

Q: 23. The __________  formula relates physical and chemical process rates to temperature and is used…

A: The Arrhenius equation gives the relation between the temperature and the rate of chemical and…

KVL and KCL

KVL stands for Kirchhoff voltage law. KVL states that the total voltage drops around the loop in any closed electric circuit is equal to the sum of total voltage drop in the same closed loop.

Sign Convention

Science and technology incorporate some ideas and techniques of their own to understand a system skilfully and easily. These techniques are called conventions. For example: Sign conventions of mirrors are used to understand the phenomenon of reflection and refraction in an easier way.