The supporting wheel on a scaffold is held in place on the leg using a 4- mm -diameter pin as shown. If the wheel is subjected to a normal force of P = 2.3 kN , determine the average shear stress developed in the pin. Neglect friction between the inner scaffold puller leg and the tube used on the whe

Q: how do we know these values if they're not given

A: Below is the answer to your query.

Q: The bell-crank mechanism is in equilibrium for an applied load of F₁ = 13 kN applied at A. Assume a…

A:

Q: Horizontal plates are connected to the bar AB whose length varies linearly from zero to HA, as…

A:

Q: For the connection shown, the average shear stress in the 14-mm-diameter bolts must be limited to…

A: Given is a double shear connection.

Q: diameter bolt is made of an aluminum alloy. It fits through a magnesium sleeve that has an inner…

A:

Q: The bell-crank mechanism is in equilibrium for an applied load of F₁ = 13 kN applied at A. Assume a…

A:

Q: The bell-crank mechanism is in equilibrium for an applied load of F1 = 19 kN applied at A. Assume a…

A:

Q: For the connection shown, the average shear stress in the 8-mm-diameter bolts must be limited to 170…

A:

Q: 2.17 In using this leg curl machine the exertion of the legs results in a torque M 120 lb-ft on the…

A:

Q: Q6/ If the allowable bearing stress for the material under the supports at A and Bis alle = 2MPA,…

A: It is mentioned that the reactions at the supports are only in vertical direction. The equivalent…

Q: The assembly is used to support the distributed load of w=500 lb/ft. determine effort normal in bar…

A: Given Force = 500 lb/ft Bar diameter = 0.4 in Bolt diameter = 0.3 in To find Normal stress in bar…

Q: A boiler with an outside diameter of 300 mm, length of 1000 mm and a wall thickness of 10 mm is…

A: According to the information we have a boiler with a diameter of 300 mm and a length of 1000 mm…

Q: The block members have a cross section of 2 in x 2 in is joined by a glued scarf spliced as shown.…

A: The ultimate normal stress on the glue surface is The factor of safety is The cross section…

Q: For the connection shown, the average shear stress in the 11-mm-diameter bolts must be limited to…

A:

Q: The bell-crank mechanism is in equilibrium for an applied load of F1 = 16 kN applied at A. Assume a…

A: Given: F1 = 16 kN  a = 330mm, b = 170mm, c = 75mm, and θ = 50° diameter =23 mm  thickness = 35 mm To…

Q: Q2/ The assembly consists of two sections of cast-iron rod connected together using a reducing…

A: Given data :- for section AB L = 12 in , d = 0.75 in for section BC L = 15 in , d = 1 in shear…

Q: Determine the force required to produce stress of 2 N/mm2 if cross sectional area is 2 mm2

A: Given data : Cross sectional area=A Stress=σ   Required : Force

Q: Determine the average normal stress developed in rod AB if the load has a mass of 50 kg.  The…

A:

Q: 3. Direct tension indicators are sometimes used instead of torque wrenches to ensure that a bolt has…

A: Write the given data with suitable variables: number of bolts=6Area of heads A=1.5 mm2strained ε=0.1…

Q: The joint fastend togather using two bolts with the plate thickness of 5mm. Determine the required…

A: given; shear stress of bolt(τ)=350MPalets take diameter of bolt=dacting load on plate(P)=40KN

Q: The rigid wrench (not the brand Rigid sold at Home Depot!) shown is used to loosen a stuck nut at…

A:

Q: Determine the magnitude of the vertical clamping force at E in terms of the force Papplied to the…

A: To determine the force at E

Q: The bell-crank mechanism is in equilibrium for an applied load of F₁ = 18 kN applied at A. Assume a…

A: F1 = 18kN a = 290mm b = 170mm c = 70mm and theta θ = 35 ° Pin B is in a double-shear connection…

Q: The bell-crank mechanism is in equilibrium for an applied load of F₁ = 11 KN applied at A. Assume…

A: Solution - given data -F1 =11KNθ =40°a =300 mmb =120 mmc =75 mm

Q: FkN dl mm dl mm 10 mm 10 mm d2 mm 10 mm d2 mm The column is subjected to an axial force(F) of 11 kN…

A:

Q: The rigid bar of negligible weight is supported as shown. The middle helical spring is made of 22 mm…

A:

Q: The rigid bar AB and CD are supported by pins at A and D. the vertical rods are made of aluminum and…

A: Given Data For bar AB L=4 ft A=0.75 in2 E=10×106 psi   For bar CD L=5 ft A=0.25 in2 E=12×106…

Q: The 10-mm-diameter bolt is made of an aluminum alloy. It fits through a magnesium sleeve that has an…

A:

Q: The two pieces of wood, 150mm x 200mm, are glued together along the 55° joint. Determine the maximum…

A:

Q: The bell-crank mechanism is in equilibrium for an applied load of F₁ = 13 kN applied at A. Assume a…

A:

Q: For the connection shown, the average shear stress in the 6-mm-diameter bolts must be limited to 176…

A:

Q: The bell-crank mechanism is in equilibrium for an applied load of F₁ = 12 kN applied at A. Assume a…

A:

Q: The d = 13-mm-diameter solid rod passes through a D = 21-mm-diameter hole in the support plate. When…

A:

Q: The lever is held to the fixed shaft using the pin AB. If the couple is applied to the lever,…

A: Given figure,  Take a point O in the centre on the line AB.

Q: The wheel on a trolley is held in place on the leg using a 5-mm-radius pin. If the wheel is…

A: The problem is asking for the average shear stress in the pin. Shear stress is a measure of how much…

Q: The horizontal shaft with a diameter of d-41 mm is supported by a thrust collar that rests on a…

A: diameter of the shaft d=41 mmthickness of the collar= 24 mmthickness of the plate =31 mmouter…

Q: Urgent. P = 18 kN

A:

Q: The yoke-and-rod connection is subjected to a 15 tensile force of 5 kN. Determine the average normal…

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.