The support points (bearings) at A and B only exert force on the components and z, on the steel shaft. Determine the diameter of the shaft, in millimeters, so that it can withstand the gear loads, without exceeding an allowable shear stress ? allowable = 80 MPa. to. Free-Body diagram. b. Shear force diagrams. c. Bending moment diagrams. d. Identification of the critical point of the axis. e. Calculation of the shaft diameter.

Q: 4- Determine the required diameter of the solid shaft BC, if the allowable shearing stress is given…

A: The total torque on the shaft BC is T=5+10=15 kNm

Q: Member ABCD is a hollow circular steel shaft with a 4 inch outer diameter and a 3 inch inner…

A: Given data:- a hollow circular steel shaft outer diameter =4 inch inner diameter =3 inch  TB…

Q: 23. The 3-segment steel shaft is loaded as shown. The length of each segment is 100 mm. Determine…

A:

Q: A power source at C actuates valves at A and B through a long round steel control rod. A torque of…

A:

Q: 1. The splined ends and gears attached to the A-36 steel shaft are subjected to the torques shown.…

A: Given data: d=40 mmShaft=A-36 steel Need to determine the angle of twist of end B with respect to…

Q: A 30 in. tubular shaft is in torsion under torque 33 lb-in.. Its cross section shown below with…

A: To find-: The shear stress at point B in psi. Given-: The torque of tubular shaft is T=33 lb.in. The…

Q: Find the section modulus of shaft having 2.5 in diameter. A 3.07 in B. 4.56 in C 5.45 in D. 8.46 in

A: Given data : Shaft of 2.5 in diameter Diameter of shaft=d   Required : Section modulus

Q: The solid spindle AB is made of a steel with an allowable shearing stress of 12 ksi, and sleeve CD…

A: Spindle AB is made of steel with allowable shearing stress of Sleeve CD is made of brass with…

Q: the diameter of solld snaft (2) IS E. 72 teeth 30 teeth (1) (2)

A: Givenspeed of motor NA=808rpmZA=24ZB=72ZC=30ZD=60

Q: Q.1) Two torques are applied to the solid bronze (G= 6500 ksi) shafts of a gear system shown below.…

A: Consider the given figure. For the shaft AB, in equilibrium condition the torque acting on the gear…

Q: 4

A: Please see the attached image for the answer.Explanation:

Q: A sketch of a bolt cutting tool is shown. Material of all parts is steel. Dimensions are in inches.…

A:

Q: Member ABCD is a hollow circular steel shaft with a 4 inch outer diameter and a 3 inch inner…

A:

Q: supplies a torque of The motor shown in Fig. 500 N· m to shaft BCDE. The torques removed at gears C,…

A: To find the torque transmitted by transverse cross-sections in BC,CD and DE of the shaft TBC=? TCD=?…

Q: angle of twist

A: .given: T1 = 10 kN-m T2 = 4 kN-m T3 = 3 kN-m. L1 = 0.55 m. L2 = 0.63 m. L3 = 0.58 m   To calculate…

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.