The structure below is subjected to a bending moment of 7kN.m, as shown in the figure. Determine (a) the reactions at supports A and C and on pin B, (b) the tensions on pins A, B and C, knowing that they have diameters of 4, 5 and 6 mm, respectively. Consider Double shear in A and C and single in B

The structure below is subjected to a bending moment of 7kN.m, as shown in the figure. Determine (a) the reactions at supports A and C and on pin B, (b) the tensions on pins A, B and C, knowing that they have diameters of 4, 5 and 6 mm, respectively. Consider Double shear in A and C and single in B

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The steel frame shown below (E = 29,000 ksi) is subjected to a single lateral force of 20 kips. The supports at D, E, and F can be assumed fully fixed, and the joints at A, B, and C are rigid. Conduct a moment distribution on the frame to determine the magnitude of the fixed-end moments at support E (in units of k-ft). Note: The moment of inertia of column CF is also 400 in“. A |= 600 in В | = 600 in C 20 kips 20 ft | = 400 in4 | = 400 in4 D E F 40 ft 40 ft
2) For the Simply Supported Beam Carrying Four point loads, as shown in the Figure, (a) Determine the reactions at points A and B. (b) Determine the shear force at points A, B, C, D, and E (c) Draw the SFD
Answer should be R=168 kn and x^- = 6m
Q.1) The beam ABC is supported by a cable at C and is subjected to two forces of 30 kN and 40 kN as shown in the figure. Determine the maximum tension on the cable and reaction forces at point A. N as shown in the figure. Neglect the thickness of the beam. A 30 kN 45° B 40 KN C 4 m D 5 m
3. A 15-kN truck having the wheel loads shown runs on top of a truss bridge as shown below. Assume the truck can travel only from left to right on the bridge. Also assume the members are pin connected at the gusset plates. The maximum tension in member BJ is mostly near: (15%) 6AN ID (A) 6kN (B) 9kN (C) 15kN (D) 18.75KN
7.16 The figure shows a steel beam which is fixedly clamped in A, and which rests on a roller bearing in B. The beam is 5 meters long, and is loaded with a bending moment of 25 kNm at the end. Determine the stock reactions in A and in B. 25 kNm 2,5 m 2,5 m
H2.
III. Using Three Moment Equation, determine all reactions at supports also, determine shear and bending moments with complete labels. Use I = 1/12 bh^3 and E = 2.15x10^7 KPa 1381 KN/m 1381 KN/m 690.5 KN/m D B 4.0 m 3.0 m 7.0 m 4.0 m b = 0.25m h = 0.50m 4.0 m b = 0.35m h = 0.70m b = 0.45m h = 0.90m
A Pin spanner as shown in Figure, requires moment of 80 Nm to turn the 200 mm diameter shaft about its center O under the action of the applied force P. determine the contact reaction force on the smooth surface at the point A. Engagement of the pin at B may be considered to occur at the periphery of the collar OPTIONS:(MULTI CORRECT(MAY BE)): 1.Reaction at Point A is around 1047 N 2.Value of force P is around 102 N 3.Value of force P is around 133 N 4.Reaction at Point A is around 720 N 5.Reaction at Point A is around 1321 N 6.Value of force P is around 200 N 7.Value of force P is around 213 N 8.Reaction at Point A is around 970 N
Answer D, E, F