The structural beam loaded as shown below is made of steel with allowable normal stress of 24 ksi. 18 kips 3 kips/ft C D A 6 ft 6ft- 3 ft Determine the reaction force at point C. O 9 kips O 27 kips

Q: Calculate the forces in members BF, BE, and EF. P=30 P kN 3 m B 3 m 3 m D 1 m 3 m 3 m E

A:

Q: For the truss shown, loads are transmitted to the bottom chord. Draw the influence diagram of member…

A: Maximum tensile force The maximum tensile load a body can sustain before failure divided by its…

Q: 6-79 The steel shaft has a circular cross section with a di- ameter of 2 in. It is supported on…

A: Step 1:Step 2: Step 3: Step 4:

Q: *6-124 The member has a brass core bonded to a steel cas- ing. If a couple moment of 8 kN m is…

A: Step 1: Step 2: Step 3: Step 4:

Q: Straight beam AE is pin-connected at its one end A and to an L-shaped beam EF at its other 2. 200 lb…

A: Free body diagram of the given problem:

Q: 7. For the beam and loading shown, determine the reaction at the roller support. The beam is W200X71…

A:

Q: FL AZ A C B D 2a a a The figure above shows a static indeterminate beam ABCD. The beam has a fixed…

A: Since A and C are simply supported MA and MC = 0 using three moments , 2MB ( L ) = 6a1x1L1 + 6a2x2L2…

Q: The A-36 steel strut AB has length 4 ft and a diameter 2 in. It is pin connected at both ends. The…

A: A-36 Struct steelL= 4ftD= 2 inchE= 29000 ksiTo determine - Maximum W load

Q: Refer to the Column Interaction Given: F’c = 27.5 Mpa Fy = 414 Column diameter 400mm Main bar…

A: Step 1: Refer to the interaction Diagram so you can find the pg. and use the formula for the Area…

Q: H.W.2: 1,200 mm The load P produces an axial strain of -1,800 ue in post (2). Determine the axial…

A:

Q: 2) Determine the tension on AB and AC and force along AD for equilibrium of the 350 kg crate. 6.5 m…

A:

Q: etermine reactions for the beam below: A L1 W E

A:

Q: 4) The rigid rods AC and BC are attached to a torsional spring of constant K = 4 kN m and a linear…

A: The given figure is shown below:

Q: The idealize model for suspension bridge is shown in the figure. The truss are pin connected at a,…

A: We have to determine the design diameter of the cable if the allowable tensile stress is 150 MPa and…

Q: For the truss structure in figure 6, draw the appropriate primary structure under unit loads of…

A: Data Given: Asked: Draw primary structure under unit loads of redundant

Q: Determine the reaction forces for girder G-1. Column A Beam B-1 L1 Beam B-2 Girder G-1 Girder G-2 L1…

A: Beams B1,B2,B3, & B4 are resting over girders G1 & G2. Total load acting on the deck and…

Bars

In civil engineering, bars refer to steel reinforcement bars or rebars. These are structural members primarily used for reinforcement purposes in masonry works. A bar is characterized by its cross-sectional area, which is negligible compared to its length. Bars are usually manufactured by steel which is uniform throughout the length, or by meshing multiple steel wires. Other materials of the bar include carbon steel, glass fiber, carbon fiber, and basalt fiber. The reinforcing bars are coated with epoxy resins and other materials to enhance some of their properties including corrosion resistance.