The stresses shown act at a point in a stressed body. The stress magnitudes are 5x = 95 MPa and Sy= 225 MPa, acting in the directions indicated in the figure. Using the equilibrium equation approach, determine the normal and shear stresses at this point on the inclined plane shown. Assume ß = 46° Answer: Sn= Snt" MPa MPa

Q: Find Wi andwe m2

A: Given data: -  The total length of string 1 is l1. The total length of the string 2 is l2. The…

Q: INFORMATION ON SOLAR THERMAL SYSTEMS

A: Solar thermal power system is a system used to concentrate solar energy that is used to produce high…

Q: how would you write this in a feature control frame. "the axis of this post should be located within…

A: Given: The cylindrical zone of 0.015 at MMC. There are three datum A,B&C. The perpendicularity…

Q: informations of thermal system

A: Thermal system s

Q: Which of the following tools is used in both marking and measuring? O Center Punch O Mallet O None…

A: Center punch is a marking tool used to mark center of a hole which is to be drilled. It is not a…

Q: is an example of Active Transducer.

A:

Q: 1 COP Nth False True

A: 1.COP=1/thermal efficiency False

Q: create Mind Map for Normalizing (heat treatment process)

A: Normalizing is a heat treatment process, heating a material above the recrystallization temperature…

Q: Which phrase is closely related to VI in Figure 2...?

A: I: Market need II:Concept: a)Define specification b)Determine function structure c)Seek working…

Q: The power of the prime mover running a pump is 20 HP, and the power out of the pump is 19 HP, what…

A:

Q: ou can collec

A: A coring is designed with central open and the method is used for shown below.

Q: d) Is that possible? e) Draw a heat engine diagram of a perpetual motion machine. f) Is it possible…

A: following is the answer to the above question

Q: In a gas turbine, the temperature of the working fluid at inlet to the compressor is 286 K and…

A: The gas turbine cycle consists of four thermodynamic processes as follows: 1-2: Work output from…

Q: A composite beam is fabricated by bolting two 2.3-in.-wide by 14-in.-deep timber planks to the sides…

A:

Q: (a) tang tan

A: Given data: Opposite side =4 Adjacent side=2

Q: means the repair work done to keep the system in good working condition.

A: we will discuss an activity/ process that is involved with work  done to keep the system in good…

Q: In a gas turbine, the temperature of the working fluid at inlet to the compressor is 289 K and…

A:

Q: Figure Q2 shows a beam subjected to distributed loading. Knowing the beam is fixed supported at one…

A: a) Free body diagram of the beam The free body diagram of the given beam is where, RB is the…

Q: Pls provide the sectional view below

A:

Q: pes of linoleum used to cover t mud

A: The simple difference is that linoleum is made from natural and renewable materials including…

Q: In a gas turbine, the temperature of the working fluid at inlet to the compressor is 286 K and…

A: This problem is based on Bratton cycle and can be solved as :

Q: 6. Nickel and titanium, at a certain alloy composition can be a ] steel alloy J crystalline material…

A:

Q: Stoker

A:

Q: Write about enhanced geothermal system

A: The enhanced geothermal system is the abbreviation of EGS and also knows as engineered geothermal…

Q: Determine the natural frequency of the system by a) the Equivalent Mass and Equivalent Stiffness…

A: (a) Write the expression of kinetic energy conservation to write equivalent mass of the system.…

Q: A 25 ft long solid steel rod is subjected to a load of 10,000 Ib. This load causes the rod to…

A: Data given -  L = 25 ft = 25 × 12 P = 10000 lb  ∆L = 0.477 in  E = 30 × 106  psi

Q: What happens to the Marin temperature factor (kd) when the desired operating temperature of a…

A: What happens to the Marin temperature factor (kd) when the desired operating temperature of a…

Q: Q4 After losing a race championship with few points, a constructor was eager to boost their vehicle…

A: In IC engines a carburetor's function is to air and fuel to supply to the engine. Its primary…

Q: PMM1 means, the machine does not follow the second law of thermodynamics Select one: True False

A: False

Q: Match each of the steady-flow engineering devices with its best description:   Question 1 options:…

A: A device that increases the pressure of a fluid by slowing it down - Diffuser  A device where two…

Q: Which hotspot on the lever below acts as the Effort?

A: This question is based on the concept of lever.

Q: From the following identify the false statement. O In electrical safety precaution, necessary steps…

A: From the above options ..

Q: In the AGMA method, one of the basic equations is o=W'K,K,K, (a) Identify this equation (select…

A: Lewis equation is used to design the gears. Lewi’s equation is the method introduced to calculate…

Q: c. PH 2. It is comp a. I C. Ar 3. Som a scr a. С. РЕ 4. It is u a. с. LF 5. It is u a.

A: Since you have posted multiple independent questions in a single question we will solve the first…

Q: Question 1 The following is an observation made during a trial on a 4-stroke diesel engine. The…

A:

Q: The rate of heat flow (conduction) between two points on a cylinder heated at one end is given by…

A:

Q: If the sensible heat ration for the heated space shown is 0.75,and supply temperature is 40 oC the…

A:

Q: 1a) The bore of each cylinder in a four-cylinder four-stroke internal combustion engine is 43 mm and…

A:

Q: Do number 13.12

A: Given Data Qr=24000 BTU/hr EER=11 Cost= 14 cents per kWh

Q: can tutor explain the questions more detailed

A: Weight on the wing, W = 80 KNLift force on the wing, F = 100 kNThe cross-sectional area of the wing,…

Q: Draw the multiple view

A: Given isometric view

Q: How did you get the values for Sc=Sb and Sa=Sd

A: To get the values of enthalpy and entropy at various points we have to consider the properties table…

Q: 6 Using the drawing callout shown in Figure 5 below, which part(s) shown in Figure 4 would now…

A: According to the given dimensional tolerance for the part, the maximum and minimum allowable…