The stress in a wire of diameter 2 mm, if a load of 100 gm is applied to a wire, is
Q: The maximum stress that a material can endure before it breaks is called Ultimate tensile strength O…
A:
Q: he frames. Considering a modulus of elasticity of 89 MPa for the rubber, assuming frames as rigid…
A: To calculate the change of force applied on the bolt . we need to calculate preload in bolt. Given,…
Q: A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as…
A: Calculate the stress in steel section.
Q: If a 110 ft steel measuring tape with a cross section of 0.008 in² is stretched with a force of 20…
A: When the tape is stretched with the help of the force, the length of the tape will increase.…
Q: 21 A firefighter weighs 730 NL She owears shoes that each cover an atea of 309 am. (a) Wihat is tthe…
A: Weight of the person F=730 N Area covered by the single shoe A1=309cm2=0.0309 m2
Q: e plates in shear, what is the shear
A: We know, Shear stress=force/Area Given, Force=47kN Diameter=3.25mm Radius=1.625mm
Q: A 1.2kg bike wheel, is spinning 210rpm clockwise when a student applies a frictional force as shown.…
A:
Q: A rod is composed of an aluminum section rigidly attached between steel and bronze sections as shown…
A:
Q: A wire can be broken by applying a load of 20 kg wt. Then force required to break the wire of twice…
A: We have formula Breaking force = stress×area Stress=Breaking forceare
Q: A force stretches a wire by 1.4 mm.
A:
Q: A vertical off-shore structure is built to withstand a maximum stress of 109 Pa. Is the structure…
A: Given : The maximum stress the structure can handle, P = 109 PaDepth of the sea, d = 3 km = 3 × 103…
Q: A tensile force of 2150 N is applied to a 12m steel beam with a cross-sectional area of 5.2 x 10-4…
A:
Q: Determine the largest weight W that can be supported by two wires shown in Fig. The stress in either…
A: Maximum weight supported by the given system of wires is equal to the sum of vertical components of…
Q: TTM i. Figure 4 shows a 12 kg weight suspended by a 0.3 m vertical copper wire with cross sectional…
A: Concept: In order to calculate the Strain in each of the wire we will firstly calculate the stress…
Q: A bar under 66,000 psi stress has a 5 square inch cross sectional area. What load is being placed…
A: Basic Details The stress applied on a bar is the internal resistance of the body for the external…
Q: material is applied by a tensile forces of 132 kN on a bar of the material with a cross- sectional…
A: stress is defined as the force per unit area. Write the expression for stress. S=FA…
Q: Calculate the force a piano tuner applies to stretch a steel piano wire by 8.00 mm, if the wire is…
A: The cross-sectional area of the wire can be obtained as
Q: T the stress experience when deformation is caused by tangential forces to the surface* O Inertia…
A:
Q: Calculate the force a piano tuner applies to stretch a steel piano wire 10.00 mm, if the wire is…
A:
Q: he unit of stress is lb/ft^2. True or false
A: Stress can be expressed in many Unit. SI unit of stress is pa (pascal) It can also expressed in…
Q: Assume that if the shear stress in steel exceeds about 4.00 108 N/m2, the steel ruptures. (a)…
A: Given, Shearing stress, S=4×108 Nm2 We know, Shearing stress , S=Shearing force(F)/Area(A) So,…
Q: The resistance to fatigue of a material is measured by (1) Elastic limit (2) Ultimate tensile…
A: The resistance of a material to fatigue is measured by the endurance limit.
Q: What is the area of the stock file if a 1.5 x 105 kg mass presses down 2.5 feet high stock file that…
A: Given that-Mass, m=1.5 × 105 kgDeformatio, ∆x= 2.7 cm=2.7×10-2 m=0.027 mHeight, h= 2.5 ft=2.5×0.3048…
Q: A body of mass 500 kg is suspended at the free end of an iron wire of length 3 m and cross-sectional…
A:
Q: A brass rod with a length of 1.40 m and a cross-sectional area of 2.00cm2 is fastened end-to-end to…
A:
Q: A very fine fabric 0.020 mm in diameter can support a 28 g object. How does the stress in the fabric…
A:
Q: A 1.05-m-long rod of negligible weight is supported at its ends by wires A and B of equal length…
A: This question involves two concepts: (A) Free body diagram and subsequent condition for the static…
Q: What pressure is required to reduce the volume of a lead block by 1% ? (Given : Bulk modulus of lead…
A: Description : In this question we have to find the pressure required to reduce the volume of lead by…
Q: Given a 2m-length rod with 37.5 mm diameter what is the actual stress (in MPa) if axial load is 19.4…
A: To calculate the stress on the rod, we need to know its cross-sectional area. The cross-sectional…
Q: What general statement can be made about the units of the quantities used to calculate strain in a…
A: A strain is defined as the amount of change per unit length of a wire when a load is applied. A…
Q: Determine the load in member AB of the pin-connected truss 3m 3m 1 m 4 m 2m A 81 B 15 68 KN E www
A: given the load in member AB of the pin-connected truss is
Q: what is the stress on a bar with n cross-sectional area of .05 sq in that is subject to a 100,000lb…
A:
Q: A metal specimen was subjected to a Vickers hardness test. The indentation on the surface of the…
A:
Q: A bar under 88,000 psi stress has a 3 square inch cross sectional area. What load is being placed…
A: The expression for the stress on the bar will be,
Q: A load of 40 kg is suspended from a ceiling through a steel wire of radius 20 mm. Find the tensile…
A:
Q: The bulk modulus for bone is 17 GPa. (a) If a diver-in-training is put into a pressurized suit, by…
A:
Q: Assume if the shear stress in steel exceeds about 4.00x 108 N/m2, the steel ruptures. Determine the…
A:
Step by step
Solved in 2 steps with 1 images
