The strain measurements from a rectangular strain rosette were so = 600 × 10-6, €45 = 500 x 10-6 and 890 = 200 x 10-6 Which of the following statements are correct? The value of shear strain in x-y plane is 200 x 10-6. Correct Option B The coordinates of centre of Mohr's circle will be (8 cm, 0) if scale is taken as 100 x 10-6 = 1 cm. The coordinates of centre of Mohr's circle will be (4 cm, 0) if scale is taken as 100 x 10-6 = 1 cm. Correct Option D The radius of Mohr's circle will be 2.23 cm if scale is taken as 100 x 10¯6 = 1 cm. Correct Option

The strain measurements from a rectangular strain rosette were so = 600 × 10-6, €45 = 500 x 10-6 and 890 = 200 x 10-6 Which of the following statements are correct? The value of shear strain in x-y plane is 200 x 10-6. Correct Option B The coordinates of centre of Mohr's circle will be (8 cm, 0) if scale is taken as 100 x 10-6 = 1 cm. The coordinates of centre of Mohr's circle will be (4 cm, 0) if scale is taken as 100 x 10-6 = 1 cm. Correct Option D The radius of Mohr's circle will be 2.23 cm if scale is taken as 100 x 10¯6 = 1 cm. Correct Option

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

please solve and exlain in neat hand writing
No need to where where the strain is located, it is my understanding that if just doing Mohrs circle and plotting Von misses right, I just wanted to check my work to make sure.
View Policies Show Attempt History Current Attempt in Progress The strain components Ex, Ey, and Yxy are given for a point in a body subjected to plane strain. Determine the principal strains, the maximum in-plane shear strain, and the absolute maximum shear strain at the point. Show the angle 8p, the principal strain deformations, and the maximum in-plane shear strain distortion on a sketch. Ex = -400 με, Ey = -310 με, and Yxy = 900 μrad. Enter the angle such that -45°≤0, +45°. Answer: Ep1 = Ep2 = Ymax in-plane - Yabsolute max. 8p= Save for Later με με 0 urad urad Attempts: 1 of 3 used Submit Answer 4
rock mechanic course
Som.
Determine the value of longitudinal strain if poisson ratio 0.23 and lateral strain -0.25
A rectangular strain gauge rosette was employed to determine o = 4350 psi and o = 1450 psi, as shown below. Calculate the magnitude of o, o and t if 0 = 30°. Note: A rectangular strain gauge rosette can be used to measure the strains and then help determine the in-situ stresses, we will discuss the use of a strain gauge later in the class, but it does not impact stress calculations here. y 02 01 Ꮎ
Name: Determine the vertical shear stress components at point q. Report your answer rounded to the nearest psi. 120 in 10 lbs/in 60 in 1500 lbs 60 in I cross section: t = 0.75" z 7=2.875" 6" 9 6.75" 1.25"
I was wrong only at yIP and yMAX please provide the 2 correct answers.
Q. 24 If the stress on two perpendicular planes through a point are 80 N/mm2 (Tensile), 30 N/mm2 (Compressive) and 50 N/mm² shear stress then the normal stress on a plane at 50° to that of tensile stress plane will be N/mm². FAQ Have any Doubt? Correct Option
For a slab with overall dimensions of 42 m x 34 m: Choose appropriate locations for the columns. Choose dimensions that allow using the ACI coefficients. The slab may be solid with drop beams (1m wide representative slab strip treated as rectangular, and drop beam treated as T-section). Alternatively, it may be ribbed with hidden beams (ribs treated as T-sections and beams treated as rectangular). Assume all columns are 75 cm x 75 cm. Dead load is that of the slab, in addition to 3cm tiles, 3cm mortar, and 13cm fill. Live load is 0.4 t/m2. Add 0.125 t/m² to the live load for partitions. Use fe' = 28 MPa, and fy = 420 MPa. a. Design the slab and the beams for flexure and shear.
Due to loading, the plate is deformed into the dashed shape shown in the figure. Assume a = 39 in., b= 33 in., δ1= 0.1625 in., δ2= 0.1 in. Determine the average normal strain along the side AB?in micro rad And answer in right and clear way Determine the average shear strain in the plate at A relative to the horizontal and vertical axes?