The step-up converter in the next figure has R = 7.5 N,L = 6.5 mH, E = 5 V, and k = 0.5. Find I₁, I2, and I.LDm+++VsS₁+E

Answered: Image /qna-images/answer/f7360575-7915-462e-90d9-b46e28cab7f0.jpg

Answered: The step-up converter in the next…

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter22: Resistive-capacitive Parallel Circuits

Section: Chapter Questions

Problem 1PP

See similar textbooks

Similar questions

A step down converter is operated with a duty cycle of k 0.75. The input voltage is V, 20V. and the load is L=5mH, R=152 The minimum inductor current is I 0.1A. The maximum inductor current is %3D %3D Select one: O a. 0.9 A O b. 1.9 A O C. None of these O d. 1.1 A O e.2A
Question 4 A boost converter has an input of 5V and an output of 20W at 15V. The minimum inductor current must be no less than 50% of the average. The output voltage ripple must be less than 1%. The switching frequency is 30kHz. Determine the duty ratio, minimum inductor value, and minimum capacitor value. Verify your answers using Matlab, show the inductor current is continues and its minimum is no less than 50% of its average. Furthermore, the output voltage ripple is less than 1%.
16 In figure H below Find Vth 17. In figure H below Find Rth 18. In figure H find Maximum Power Transfer at RL +24 V H. 100 15 0 RL 150 www 20 0
I need answer with explaination In a series R–L circuit the p.d. across the resistance R is 12V and the p.d. across the inductance L is 5V. Find the supply voltage and the phase angle between current and voltage
For the following figure, find the total impedance and total current. Explain what is relation between XL and Xc. Find the voltage drops in inductor, capacitor and resistor. XL = 1.8 k VT-15 V R-450 www Xc-1.2 kn
i need Full detailed Steps
Design a clamper circuit with the below waveform: -4 V -36 V
OUTPUT VOLTAGE (V) 2.0 1.8 1.6 1.0 0.8 0.6 0.2 0 <-50 a. TMP35 b. TMP36 c. TMP37 +Vs = 3V -25 0 50 25 TEMPERATURE (°C) 75 Figure 6. Output Voltage vs. Temperature 100 b 125 00337-007 Using the appropriate curve, develop a linear equation for the output temperature as a function of voltage.
The high voltage arm of an RC divider has 10x100 ohms resistors with a 15-pF capacitor to the ground from each of the junction points. The ow voltage arm resistance is 10 ohms. Determine the capacitance need the LV arm for correct compensation.
find zener voltage and resistance with given values:capacitor: 470 micro Fresistor: 12 ohmV out: 12V DCI out: 1AV in: 120V AC 60 Hzdiode: 0.7V
Sketch the output waveform of the circuit shown in figure below. Also give explanation of the waveform.
1

SEE MORE QUESTIONS

Recommended textbooks for you

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

The step-up converter in the next figure has R = 7.5 N, L = 6.5 mH, E = 5 V, and k = 0.5. Find I₁, I2, and I. L Dm ++ + Vs S₁ + E