The steel rod has a radius of 1.25 in. If it is subjected to a shear of V = 5 kip, determine the maximumshear stress.1.25 in.V= 5 kip2.

Answered: Image /qna-images/answer/5645af2f-82ec-447b-9a26-975ab4756433.jpg

Answered: The steel rod has a radius of 1.25 in.…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

4. Part AB of the bar has a solid circular cross section and part BC has a hollow circular cross section. The bar is fixed at both ends and a 150-in-kip axial torque is applied at B. Suppose that you want to decrease the weight of the bar by increasing the inside diameter of part B. The bar is made of material that will safely support a pure shear stress of 10 ksi. Based on this criterion, what is the largest safe value of the inside diameter? 4 in 2 in 150 in-kip A -14 in 7 in
The triangular plate is fixed at its base, and its apex A is given a horizontal displacement of 5 mm. Calculate the shear strain, Yxy, at A. Also, calculate the average normal strain & along the x' axis. 800 mm 45% 45° 800 mm 5 mm
Ans (P) - 50.4KN need explanation
Rigid bar ABCD is loaded and supported as shown. Steel [E = 29900 ksi] bars (1) and (2) are unstressed before the load P is applied. Bar (1) has a cross-sectional area of 0.81 in.2 and bar (2) has a cross-sectional area of 0.46 in.2. After load P is applied, the strain in bar (1) is found to be 770 με. Assume L1=55 in., L2=78 in., a=31 in., b=31 in., and c=36 in. Determine: (a) the stresses in bars (1) and (2). (b) the vertical deflection vD of point D on the rigid bar. (c) the load P.
Steel plate (2) b. 4. Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses acting on horizontal and vertical planes at the point are shown. a. 8.5 ksi 5.7 ksi 10.5 ksi Draw Mohr's circle for this state of stress. Me grapting page is ba b. Determine the principal stresses and the maximum in-plane shear stress acting at the point. Ans. c. Show these stresses on an appropriate sketch. <
Problem 6 For the structure shown in the figure, determine the normal and shear stresses at point A on the cross section of the pipe. at section a-a. mun 40 mm 300 mm 300 mm
A hollow aluminum tube used in a roof structure has an outside diameter d2= 112mm and an inside diameter d1= 80mm. The tube is 2.80m long, and the aluminum has a shear modulus of G= 28GPa.a. If the tube is twisted in pure torsion by torques acting at the ends, what is the angle of twist, in degrees,when the maximum shear stress is 52MPa?b. What diameter d, in mm, is required for a solid shaft, as shown, to resists the same torque with the same maximum stress?c. What is the ratio of the weight of the hollow tube to the weight of the solid shaft?
The hollow circular beam is fixed to the wall (with a bracket) on the left and has an end-cap on the right. The cross-section is shown. (a) Determine state of stress at point A & draw the stress element (b) Determine state of stress at point B & draw the stress element A 100 k-in Tout 2 in n=1.75 in В. B 40 k-in C Tout 30 k X
Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses acting on horizontal and vertical planes at the point are shown. If o- 29 MPa in the direction shown, determine the principal stresses at the point. 28 MPa 16 MPa O 42.4 MPa and -29.4 MPa O 26.2 MPa and -17.7 MPa O 53.1 MPa and -37.9 MPa O 45.4 MPa and -31.0 MPa O 34.1 MPa and -24.6 MPa

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

The steel rod has a radius of 1.25 in. If it is subjected to a shear of = 5 kip, determine the maximum shear stress. -1.25 in. V= 5 kip