The steel rod ABC is made of a steel for which the yield strength is y = 250 MPa and the modulus of elasticity is E = 200 GPa. Determine, for the loading shown, the maximum strain energy that can be acquired by the rod without causing any permanent deformation.

Q: The normal strain in a suspended bar of material of varying cross section due to its own weight is…

A:

Q: 2. If the load P on the beam below causes the end C to be displaced 10mm downward, determine the…

A:

Q: A bar BD is held in a horizontal position when there is no load by the steel wire AB. When a weight…

A: The cross sectional area of wire is The modulus of elasticity is The yield strength is The…

Q: ented ass shown. Determine the stress at point would the stress be at point A if the couple M is o…

A: find the principal axis ;average moment of inertia ,  corresponding to the point E  substitute…

Q: 1. Determine the resultant internal loadings acting on the cross-section at C of the simply…

A: As per expert guidelines we are supposed to answer only the first question of the given multiple…

Q: Ql: The stresses measured at a point on bone are o, =5 MPa ,0, = -7 MPa and t-2.4 MPa find: 1. The…

A: Permissible stress is stress which produces due to pressure or forces which does not exceed the…

Q: prismatic bar of length L is subjected to axial load P. Determine the maximum strain & along the bar…

A:

Q: Part of a control linkage for an airplane consists of a rigid member CB and a flexible cable AB.…

A: Given data  To determine   which of the following statement is false 1 B' is located directly to…

Q: A thin rectangular polymer plate PQRS of width b = 410 mm and height a = 154 mm is shown in the…

A:

Q: 10 ksi, o, = -4 ksi, and 29 x 103 ksi and poissons ratio is 0.3, determine the normal strain along…

A:

Q: Tube with 100 mm long and 20 mm diameter. If the axial load is 30or .applied to it. Determine the…

A:

Q: A thin triangular plate PQR forms a right angle at point Q. During deformation, point Q moves to the…

A:

Q: New Tab 15MDlxNzMz/a/NDCONZAWMTQYMTK3/details Open wi 3. A rigid member CBD is supported by a…

A:

Q: In a laboratory test of a beam loaded by end couples, the fiber at layer AB as shown are found to…

A:

Q: 2. Assuming the end of C is moved 10mm downward by a load P on the beam, determine the normal strain…

A:

Q: 10 ksi, oy -4 ksi, and o, = 8 ksi. Using E = The normal stresses at a point in a steel member are o,…

A: Answer: The normal strain along z is (0.2138 × 10-3) in/in.

Q: The load P produces an axial strain of –1,800 µɛ in post (2). Determine the axial strain in rod (1).…

A:

Q: 1) Load P is applied to the fixed-supported symmetrical I profile beam. The beam material is steel,…

A: “Since you have posted a question with multiple sub-parts, we will provide the solution only to the…

Q: 2 m 1.5 m 3 m- -2 m B

A:

Q: When subjected to a compressive load, the length of the rod is 199,6 mm, and its diameter is 10 mm.…

A: GIVEN DATA-  Final length of the rod is 199.6 m Intial Length 200mm Diameter d=10mm E=70GPa

Q: The two bars are used to support load P. When unloaded, joint B has coordinates (0, 0). After load P…

A:

Q: if the rod is subjected to a tensile load P = 6 kN, and has a diameter of 44 mm. if the modulus of…

A:

Q: If the copper in no. 2 is changed into steel with the same dimensions and with a modulus of…

A:

Q: The man has a mass of 84 kg and stands motionless at the end of the diving board. Figure -1.5 m B…

A:

Q: 1. Neglecting the weight of the steel wire, determine its required diameter if it is 30 ft long,…

A: Given data,  L= 30 ft = 360 in Elongation ∆L= 0.4 in   P= 500 lb  E= 49*10⁶ psi  Stress limit s=…

Q: A sheet of copper is stretched biaxially in the xy-plane. If the strains in the sheet are…

A:

Q: A load of P=3.1 kip is applied to the A-36 structural- steel beam. The modulus of elastisity and…

A:

Q: Athin triangular plate PQR forms a right angle at point Q. During deformation, point Q moves to the…

A: The shear strain at corner Q'.Given:The horizontal deformation is .The vertical deformation is .The…

Strain energy

The term strain indicates the variation in an object's length, area, and volume when the object is subjected to an external force. The external force may be of normal, shear, moment, torque, etc. The strain in an object depends on the types of external force and cross-section of the object. Mathematically, the evaluation of strain can be obtained with the help of elastic constants.