The steel (E= 200 GPa) I-beam (W530 x 66, I= 351 x 10° mm) has a fixed support at A and is subjected to a distributed load over its entire length. The distributed load causes the roller support at B to settle downward (displace downward) by 10 mm. Determine the reactions at supports A and B. 70 kNm IC 10 mm 4.5 m 1.5 m

The steel (E= 200 GPa) I-beam (W530 x 66, I= 351 x 10° mm) has a fixed support at A and is subjected to a distributed load over its entire length. The distributed load causes the roller support at B to settle downward (displace downward) by 10 mm. Determine the reactions at supports A and B. 70 kNm IC 10 mm 4.5 m 1.5 m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

a) The fixed-end bar ABCD consists of three prismatic segments, as shown in the figure Qla. The end segments have cross-sectional area A1 = 800 mm and length L1 = 200 mm. The middle segment has cross-sectional area A2 = 1500 mm and length L2 250 mm. Loads Pg and Pc are equal to 30 kN and 20 kN, respectively. A1 A2 A1 PB D В L2- Figure Qla i) Determine the reactions Ra and Rp at the fixed supports. ii) Determine the compressive axial force FBc in the middle segment of the bar. iii) Determine the displacement of C with respect to B due to the compressive load. iv) If all the lengths and area are double, what happen to your answers in (i), (ii) and (iii)
The beam is subjected to applied loads as shown. Determine the reactions at the supports. (Check all correct answers) *
i need the answer quickly
6. Draw a free body diagram for the member CB of structure shown below. P P 2 m D C 30 2 m 2 m B A 2 m
For the suspended load F = 637lb in the figure. Find the magnitude of the reaction of the patella at O.
The three concentrated load is supported by a T beam shown in figure. Determine the maximum value of P so that Gensile ≤ 12 ksi and compressive ≤20 ksi. 2in K 3P 4ft 7ft R₁ 7ft 4ft R₂ k4in 8in 2in
The rigid beam ACE is fixed by both sides as shown in figure, if F1 = 300 kN and F2 = 150 kN. Find the reactions Ra and Rb. Take S = 3.5 mm and E=200 (GPa):
Question 1 For the plane trusses shown in the figures, all elements have E = 100 GPa and A = 40 x 10-4 m². Determine the horizontal and vertical displacements of node 4 4 m 60* 5m 45° 50 kg 5m
5 kip/ft ( parabolic (2nd order) 3 C В -10 ft -10 ft The structure above is supported by a rocker at A and a pin at B. The structure is subjected to a parabolic (i.e. second order) distributed load, as shown. Assume that the rocker at A can resist a compressive or tensile normal force. Which of the following is closest to the vertical force reaction at the pin (i.e. By)? a) 50 kip b) 0 c) 22.5 kip O d) 33.3 kip
The rigid member ABC is supported by steel wire (AE), pin support at B, and aluminum block CD as shown. The steel wire AE has A = 22.5 mm² and E = 200 GPa. Aluminum block CD has A = 40 mm? and E = 70 GPa. Under the applied load (P) determine the vertical deflection at A. Use the table given below and your student ID to find the values of L, L, and P. E A 150 mm 100 mm 150 mm Student L. (ttnir) (N) 150 ID (mm) 1131731 100 325 P.
Q11
Motiyo Add explanation