The steam turbine shown below has a single inlet and two exit streams. It is assumed that the turbine is well insulated and the change in potential energy is negligible. The energy equation governing the turbine based on these assumptions is: Turbine inlet 1 W. C.V. C.V. 3.

The steam turbine shown below has a single inlet and two exit streams. It is assumed that the turbine is well insulated and the change in potential energy is negligible. The energy equation governing the turbine based on these assumptions is: Turbine inlet 1 W. C.V. C.V. 3.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

115 m turbine 2 In the above example problem, a hydroelectric turbine at the base of a dam is shown schematically. The height of the water above the turbine station given as 115 m. This turbine produces 4.6 MW of electricity, and you may assume the losses in the system to be equivalent to 10 m of head of water. The diameter of the pipe at the turbine exit is 0.75 m, and the velocity of water exiting from the pipe is 12.5 m/s. Caleulate the efficiency of the turbine.
a hydraulic turbine receives water froma reservor at an elevation of 100 meter above it. what is the minimum water flow in (kg/sce) to produce a steady turbine output of 50 mw?
Q2/ A 1.343 x 10' J fan is used in a large room to provide for air cireulation. Assuming a well insulated, sealed room, determine the internal energy increase after I hour of operation.
In the jet impact experiment, water jet impacts on a curved vane in the vertical direction. As shown in the figure below, the exit has an angle with respect to the vertical direction. The distance from the nozzle to the vane surface at the exit is h. The water volume flow rate is measured to be Q, the density of water is p, and the cross section area of the nozzle is A₁. Assume that the flow has reached the steady state. (1) Use the Bernoulli's equation to determine the velocity Vout at the exit of the vane. Assume that friction between water and the curved vane can be neglected. (2) Apply the Reynolds transport theorem to derive the expression of the impact force F, on the curved vane (neglect the jet weight). (3) Under the condition of a fixed volume flow rate Q, determine the maximum impact force Fr,max that can be obtained when the angle varies (e.g. in different vane designs). Va out 9 Ao Vout h
Q4. Water from a reservoir is conveyed via a pipeline of constant diameter and 1000m length to a turbine situated 90m below the reservoir surface level. The velocity of flow through the pipeline is 5m/s and the energy loss due to friction in the pipeline is 200J/kg. The water leaves the turbine at atmospheric pressure (100 kN/m2) and with negligible velocity. Assuming an efficiency of 85% for the turbine, determine: a). Pipeline diameter b). Pressure at entry to turbine c). Turbine power output. Take f = 0.025
The difference in elevation between the surface of the water in a storage reservoir and the intake to a turbine was 130 ft. it has a discharge of 45 ft3/s. If the inside diameter of the penstock is 37 inches, find the penstock efficiency.
4. to convert the kinetic energy of water into the mechanical shaft energy. Water enters the turbine, at the inlet, with the velocity Vin = 40m/s and the mass flow rate m=1,000kg/s. Water exits the Vi,z40ms turbine with a negligible velocity, say, Vout = 0 m/s.The efficiency of m - loooly/s Figure on the right shows a hydraulic turbine designed HzO HzO the turbine is 75 %. Potential energy and flow work can be ignored. 4а. Please calculate the specific kinetic energy of water entering the turbine ( ɛr or ke; in J/kg). 4b. Please calculate the rate of total kinetic energy of the water flow ( É̟ or KĖ ; in J/s or W) 4с. Please determine the mechanical power output of this turbine (Wou; in W or kW). 4d. Please determine how much mechanical energy would this turbine generate during an hour
Q4/ A rigid tank contains hot fluid that is cooled while being stirred by a paddle wheel. Initially, the internal energy of the fluid is 800 kJ. During the cooling process, the fluid loses 500 kJ of heat, and the paddle wheel does 100 kJ of work on the fluid. Determine the final internal energy of the fluid. Neglect the energy stored in the paddle wheel. Qout=500 kJ U₁ = 800 kJ U₂ = ? Fluid Figure (2) Wsh.in = 100 kJ
Steam flows into a turbine at the rate of 10 kg/s and 10 kW of heat are lost from the turbine. Ignoring elevation and kinetic energy effects, calculate the power output from the turbine.Note : h1 = 2739 kJ /kg and h2 = 2300.5 kJ / kg CHOICES: A. 4605 kW B. 4973 kW C. 4375 kW D. 4000 kW
BOILER |Pump Exit T, = 40°C P1 = 15.0 MPa Boiler Exit T2 = 550°C P2 = 15.0 MPa The pump shown in the figure is used to pump 36,000 kg of compressed liquid water per hour into a boiler. Pump exit conditions are 40 °C and 15.0 MPa. The boiler discharges steam at 550 °C and 15.0 MPa (mass flow of steam discharged equals mass flow of water pumped in). Find the rate at which heat must be generated by the boiler, Q , in units of MW (1 MW = 1 million Watts). MW
60 degree F water flows through a horizontal turbine. The water speeds at the turbine inlet and the turbine outlet are identical. The water gage pressure at the turbine inlet is 46.4 psi while that at the outlet is 12.2 psi. Assume water frictional losses through the turbine are negligible. Deterimine the shaft work rate in ft*lb per slug of water passing through the turbine. Answer with a positive number if mechanical energy goes into the water and a negative number if mechanical energy comes out of the water as it passes through the turbine.
Superheated steam at 40 bar absolute and 500°C flows at a rate of 250 kg/min to an adiabaticturbine, where it expands to 5 bar. The turbine develops 1500 kW. From the turbine thesteam flows to a heater, where it is reheated isobarically to its initial temperature. Neglectkinetic energy changes.(a) Write an energy balance on the turbine and use it to determine the outlet streamtemperature.(b) Write an energy balance on the heater and use it to determine the required input (kW) tothe steam.(c) Verify that an overall energy balance on the two-unit process is satisfied.(d) Suppose the turbine inlet and outlet pipes both have diameters of 0.5 meter. Show that itis reasonable to neglect the change in kinetic energy for this unit.