The state of stress at a point in a member is shown on the element. Suppose that o, = -50 MPa , oy = -120 MPa, Try = -30 MPa Part A Determine the normal stress component acting on the plane AB. (Figure 1) Express your answer with the appropriate units. HA Value Units Submit Request Answer Figure 1 of 1 Part B A Determine the shear stress component acting on the plane AB. Express your answer with the appropriate units. HA ? 30% Tr'y = Value Units Submit Request Answer B

The state of stress at a point in a member is shown on the element. Suppose that o, = -50 MPa , oy = -120 MPa, Try = -30 MPa Part A Determine the normal stress component acting on the plane AB. (Figure 1) Express your answer with the appropriate units. HA Value Units Submit Request Answer Figure 1 of 1 Part B A Determine the shear stress component acting on the plane AB. Express your answer with the appropriate units. HA ? 30% Tr'y = Value Units Submit Request Answer B

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Remake the diagram for this problem. Empasize the area of 1,2,3, 4 and refer to the solution. No need to solve. Just the diagram
The state of stress acting at a critical point on a wrench is shown in the figure. Pi P2 - 340 MPa Part A خ == .0 P₁ OY = Value P. Determine the smallest yield stress for steel that might be selected for the part, based on the maximum shear stress theory. Express your answer to three significant figures and include appropriate units. Units P110 MPa and EDIT ? C
tao_abs max = 87.9MPa
Two rods support the rigid bar ABC as shown in the figure. A downwards load P of 50 kN is applied at A. Rod BD has the following properties: L = 600mm, E = 73 GPa, and A = 1,250 mm². Rod CE has the following properties: L = 400mm, E = 200 GPa and A = 750 mm2. Indicate negative if under compression or if the member contracteri D 200 mm Εἴ 400 mm B 600 mm 300 mm-
Question 2 For the stresses of plane stress state is ox = -8 MPa , Oy = 7 MPa and Txy = -6 MPa Draw a Mohr's circle diagram. Draw stress element for the given stresses Find the principal normal and shear stresses, and determine the angle from the x axis to ơ1 Draw the stress element for the principle stress. Using stress transformation, find the principle stresses and the angle of o, Determine the stress transformation for the angle Ø = 25°
I need answer within 20 minutes please please with my best wishes
Solid Mechanic Chapter 5 (Stress Transformation Equiation) please show the full calculation. Thank you
Figure 200 mm 400 mm -20 mm A Section a-a Determine the state of stress at point A on the cross section of the pipe assembly at section a - a. Take F₁ = 1520 N, F₂ = 1100 N. (Figure 1) Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive in the case of tension. A = 49.6 μA Submit Previous Answers Request Answer Part B X Incorrect; Try Again; 7 attempts remaining (Tzy) A = MPa Find (Tzy) A- Express your answer to three significant figures and include the appropriate units. ΜΑ Value ? Units ?
The tank of the air compressor is subjected to an internal pressure of 0.43 MPa as shown in (Figure 1). The internal diameter of the tank is 550 mm, and the wall thickness is 6 mm. Figure ⁹-1 Y Y Part A Determine the hoop stress acting at point A. Express your answer to three significant figures and include the appropriate units. 0 = Submit Part B 02 = Submit O Provide Feedback HA Value Request Answer Determine the longitudinal stress acting at point A. Express your answer to three significant figures and include the appropriate units. Value HÅ 1 h Units Request Answer Units ? F ?
In (Figure 1), y = 13.9 ksi. Figure 10 ksi < 20 ksi 1 ▼ Determine the principal stresses. Specify the orientation of the element. Express your answers, separated by commas, to three significant figures. 01, 02, 0pl = Submit Part B T in-plas 195| ΑΣΦ | it | vec Request Answer Submit =, avg=, 0,= 1 Request Answer Determine the maximum in-plane shear stress and average normal stress. Specify the orientation of the element. Express your answers, separated by commas, to three significant figures. d 195] ΑΣΦ | it Ivec BARC 5 → C ? www. ksi, ksi, (clockwise) ? 0 ksi, ksi, (clockwise)
Consider the plate shown in (Figure 1). Figure 0.45 in. 3 in 0.54 in. 0.45 in. 1 of 1 0.5 in. 4.5 in. P ▼ Part A Determine the maximum axial force P that can be applied to the plate. The allowable stress is allow = 51 ksi. Express your answer to three significant figures and include the appropriate units. HÅ P= Submit Value Units Previous Answers Request Answer < Return to Assignment X Incorrect; Try Again; 5 attempts remaining ? Provide Feedback
ans c please fast