Answered: The state of stress at a point in a…

The state of stress at a point in a loaded member is shown in the figure. The magnitude of maximum shear stress is [1MPA = 10 kg/cm²] 40MPA %3D = 30MPA 0, =-40MPA 0, =-40MPA = 30MPA %3D = 40MPA

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

When an axial load is applied to the ends of the bar shown in the figure, the total elongation of the bar between joints A and C is 0.17 in. In segment (2), the normal strain is measured as 1,450 uin./in. Assume L₁ - 45 in. and L₂ - 94 in. Determine (a) the elongation of segment (2). (b) the normal strain in segment (1) of the bar. P A Answers: L₁ (a) in.₂ = i (b) £₁ = i B (2) L2 in. uin./in.
The tensile stress in the AB bar is in the BC bar in order for it to be the same as the pressure stress, the Force P in the figure must be how many. F=170 N , LAB=85 mm , LBC=85 mm , DAB=51 mm , DBC=102 mm
Try One scene 7 of 7 The bar has a 90 mm by 20 mm rectangular cross section. If P = 80 kN, determine the force components perpendicular (N) and parallel (V) to a – a, the inclined surface area, and the normal and shear stress magnitudes acting on surface a – a. 90 mm 62° a N kN kN Aa-a mm2 P = 80 kN MPa MPа Try one 1st 2nd 3rd Enter attempt
An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown in the figure below. Axial loads are applied at the positions indicated. Find the maximum value of P that will not exceed a stress in steel of 200 MPa, in aluminum of 115 MPa, or in bronze of 145 MPa. Aluminum A = 400 mm2 Bronze A = 200 mm2 Steel A = 500 mm² P 2P 4P 2.5 m 2.0 m 1.5 m
B1
Fill in the blanks: The steel rod is stress-free before the axial loads P₁ =169 kN and P2 = 88 kN are applied to the rod. Assuming that the walls are rigid, calculate the axial force in each segment after the loads are applied. Use E-200 GPa. A = 2000 mm² A = 900 mm² A = 1200 mm² P P₁ B с D -250 +₁3 500 mm mm- 350 mm- ANSWER: KN, PBC = PCD = KN KN, PAB = (express it in whole number) A
In mechanical resistance
The temperature of an aluminum bar and a steel bar was raised from 40°C to 160°C. If there was a gap 0.4 mm between the two bars at 40°C as show in figure below, determine the normal stress in the aluminum bar and the change in length of the aluminum bar. 0.5 mm 300 mm 250 mm B Aluminum Stainless steel A = 2000 mm² E = 75 GPa A = 800 mm² E = 190 GPa a = 17.3 x 10-6/°C %3D %3D a = 23 X 10-6/°C
250 mm Q1: The beam shown in Figure 1 is subjected to a vertical force Py and a horizontal force Pr The data for P Pr, a L,and e are shown in Table1. Determine the maximum compressive and tensile stresses under the vertical force (at a distance a from the left support.) Pv > 135 KN 55 omm a I=> 6omm Ph 2248KN 120 mm L =2 600mm Figure 1
Determine the normal stress in each segment of the steel rod shown in the figure. E-200 GPa. A = 600 mm² A B 300 KN + 0.3 m A 200 mm² 200 KN 0.3 m 0.4m D 100 kN