The state of a plane strain at a point has the components &, = -100 (10-5), &y = -50 (10-5) and yw = 200 (10-5). Determine the principal strains and the maximum in plane shear strain. Select one: & = 28 (10), E2 = 178 (10°) and Ymax in-plane = - -206 (10). 228 (106), ɛ2 = 178 (10°) and ymax in-plane 206 (106). %3D %3D O & = 28 (10), ɛ2 = -178 (10°) and ymax in-plane 206 (106). %3D %3D O = -28 (10), ɛ2 = -178 (10) and ymax in-plane = 206 (10°). O & = 28 (10), e2 = 178 (10°) and ymax in-plane = 206 (10). %3D

The state of a plane strain at a point has the components &, = -100 (10-5), &y = -50 (10-5) and yw = 200 (10-5). Determine the principal strains and the maximum in plane shear strain. Select one: & = 28 (10), E2 = 178 (10°) and Ymax in-plane = - -206 (10). 228 (106), ɛ2 = 178 (10°) and ymax in-plane 206 (106). %3D %3D O & = 28 (10), ɛ2 = -178 (10°) and ymax in-plane 206 (106). %3D %3D O = -28 (10), ɛ2 = -178 (10) and ymax in-plane = 206 (10°). O & = 28 (10), e2 = 178 (10°) and ymax in-plane = 206 (10). %3D

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The strain components ɛ, Ey, and yxy are given for a point in a body subjected to plane strain. Using Mohr's circle, determine the principal strains, the maximum in-plane shear strain, and the absolute maximum shear strain at the point. Show the angle 0p, the principal strain deformations, and the maximum in-plane shear strain distortion in a sketch. Ex = 0 µE, ɛ, = 320 µɛ, Vxy = 240 µrad. Enter the angle suen that -45° s 0,s+45°.
The two bars shown in the figure are used to support a load P. When unloaded, joint B has coordinates (0, 0). After load P is applied, joint B moves to the coordinate position (0.25 in., -0.70 in.). Assume a = 13 ft, b = 7 ft, and h = 10 ft. Determine the normal strain in each bar. Answers: EAB= EBC= i a B b με με X h
2
2
43° 30° 15° A strain gage rosette has been placed on a solid member as shown in in the figure to perform stress analysis on a mechanical system. The given values of strain has been obtained. E = 121x1- E2 = 304x10-6 Ez = 203x10-6 Material properties of the solid body are, E = 207 Gpa and v = 0.29. For this case, calculate normal and shear stress values which occurs on the body.
(b) A differential element on the bracket as shown in Figure Q1 is subjected to plane strain that has the following components: ex = 150µ, ey = 200μ , γχν = -700μ. By using the strain transformation equations, determine:- The equivalent in-plane strains on an element oriented at an angle 0 = 60° counterclockwise from the original position. (ii) Sketch the deformed element within the x' – y' plane due to these strains. (iii) The stresses on the oriented planes in (i) where the value of elasticity, E = 200 GPa and Poisson's ratio, v = 0.32. (iv) Give your comments on those stresses in (iii) in terms of elastic limit/failure if the material's yield strength in tension/compression is 250 MPa and in shear is 90 MPa.
Deformed length of the elongated diagonal.
The 45° strain rosette is mounted on the surface of a shell. The following readings are obtained for each gage: Pa = -200(10-6), Pb = 300(10-6), and Pc = 250(10-6). Determine the in-plane principal strains.
Determine the deformed length of the elongated diagonal
Q1: The stresses measured at a point on bone are oy =5 MPa ,o, = -7 MPa and 1,,=2.4 MPa find: 1. The principal strains and maximum shear strain. 2. The strain energy . Knowing that the poisonratio v=0.3 and the unit volume change =5.6x10
A 45° strain rosette (see figure 4) mounted on the surface of a car chassis gives the following readings: εA = 310×10−6, εB = 180×10−6 and εC = −160×10 −6. Determine the principal strains and maximum shear strains and show them on appropriately oriented element diagrams.
1