The standard length of a tape is 100m having a weight of 1.2kg with the standard temperature of 20 ̊C and standard pull of 5.5kg. The young modulus of elasticity of the tape is 200GPa, cross sectional area is 2.8mm2 and the coefficient of linear expansion is 0.0000116/ ̊C. Determine the normal tension of the tape.

The standard length of a tape is 100m having a weight of 1.2kg with the standard temperature of 20 ̊C and standard pull of 5.5kg. The young modulus of elasticity of the tape is 200GPa, cross sectional area is 2.8mm2 and the coefficient of linear expansion is 0.0000116/ ̊C. Determine the normal tension of the tape.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

4.c
A steel bar, whose cross section is 0.60 inch by 4.10 inches, was tested in tension. An axial load of P = 31,025 lb. produced a deformation of 0.115 inch over a gauge length of 2.10 inches and a decrease of 0.0080 inch in the 0.60-inch thickness of the bar. a. Determine the lateral strain. b. Determine the axial strain. c. Determine the Poisson’s ratio v. d. Determine the decrease in the 4.05-in. cross-sectional dimension (in inches).
All of the following statements are correct except:a. Materials with higher modulus of elasticity, E are relatively weaker than those with lower E.b. Stress is proportional to strain within the elastic range.c. High carbon steel is stronger than concrete.d. In normal loading, the slope of the stress-strain curve is a material property called modulus of elasticity.The deflection of a beam is: A. Directly proportional to the modulus of elasticity and Moment of inertia B. Inversely proportional to the modulus of elasticity and moment of inertia C. Directly proportional to the load imposed and inversely to the length squared D. Inversely proportional to the weight and length
A steel rod is rigidly attached between an aluminum and bronze rod. The diameters of eachmaterial are shown in the figure. A fixed support is rigidly attached to the right end of thebronze rod. Determine the stress each section in KPa.
Part 2 * Your answer is incorrect. The z-component of momemt M will cause compression at A and B, and tension at C and D. The y-component of moment M will cause compression at A and D, and tension at B and C. The maximum tensile bending stress will occur at point C. Calculate the magnitude of the largest bending moment that can be applied so that the stress at corner C does not exceed 205 MPa. Answer: M- eTextbook and Media Save for Later Part 3 8.31E1 Answer: M-i The z-component of moment M will cause compression at A and B, and tension at C and D. The y-component of moment M will cause compression at A and D, and tension at B and C. The maximum compressive bending stress will occur at point A. Calculate the magnitude of the largest bending moment that can be applied so that the stress at corner A does not exceed 205 MPa. eTextbook and Media Save for Later Part 4 kN-m * Your answer is incorrect. kN-m Submit Answer Determine the maximum bending moment that can be applied to this cross…
Please answer it properly don't waste my question I will vote it up for your effort thank you.
SITUATION. As shown in the figure below, a rigid bar with negligible mass is pinned at O and attached to two vertical rods. Assume that the rods were initially stress-free. Allowable stress in steel is 120 MPa and in bronze is 60 MPa. For this problem, a = 1.8m; b = 1.3m; c= 1.7m. a b C P Steel: A-900 mm² Bronze: A=1200 mm² E = 83 GPa L=2.0 m E = 200 GPa L=1.5m What is the value of P without exceeding the allowable stress of bronze, in kN? O 161 O 174 O 145 124 4
An aluminum [E = 11500 ksi] control rod with a circular cross section must not stretch more than 0.21 in. when the tension in the rod is 2080 lb. If the maximum allowable normal stress in the rod is 11.5 ksi, determine: (a) the smallest diameter d that can be used for the rod. (b) the corresponding maximum length L of the rod. Answers: (a) d = i (b) L = i in. in.
2. Shown below are pieces of unsaid material. They are combined and locked in each other and a force P is pulling each side. Assuming that the Shear stress for the material is 38 MPa, Determine the force P needed to fracture the materials in shear. 30 mm 30 mm 80 mm Section A-A
A steel rod of 20mm is enclosed centrally in a hollow copper tube of external diameter 40mm and internal diameter of 35mm the composite bar is then subjected to an axial pull of 50KN.If the length of each bar is equal to 200mm,determine 1.The stress in the rod and the tube 2.Load carried by each bar Take E for steel=200KN/mm2 and copper =100KN/mm2
Give me right solution with clear hand writing.
The composite bar of neglible mass is connected to two rods as shown in the figure. If the system is initially free, determine the temperature change that will cause a tensile stress of 60 Mpa in the steel rod.