THE SPRING RATE FOREACH OF THE SPRINGATTHE 1ST LEVEL AREALL 270 Mm, 2NDLEVEL AT I8O N/mAND 3RD AND HTHLEVEL AT 9ON/m. IF4.THE HEART HAS A160MASS OF 160 kg,WHAT IS THE LENGTH OF SPRINGS ONEACH LEVEL AND WHAT IS THETOTAL DEFLECTON ? [9=9-ro m/s]AL PER LEVEL:-TOTAL Y:1st Level Deflection=2nd Level Deflection =malth3rd Level Deflection=TS4th Level DeflectionTotal Deflection

Name: THE SPRING RATE FOREACH OF THE SPRINGATTHE 1ST LEVEL AREALL 270 Mm, 2
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: THE SPRING RATE FOREACH OF THE SPRINGATTHE 1ST LEVEL AREALL 270 Mm, 2NDLEVEL AT I8O N/mAND 3RD AND HTHLEVEL AT 9ON/m. IF4.THE HEART HAS A160MASS OF 160 kg,WHAT IS THE LENGTH OF SPRINGS ONEACH LEVEL AND WHAT IS THETOTAL DEFLECTON ? [9=9-ro m/s]AL PER

The first level deflection can be determined as shown below.

Answered: THE SPRING RATE FOR EACH OF THE SPRING…

Engineering

Mechanical Engineering

THE SPRING RATE FOR EACH OF THE SPRING ATTHE 1ST LEVEL ARE ALL 270 Mm, 2NO LEVEL AT IBO Nim AND 3RD AND HTH LEVEL AT 90N/m. IF THE HEART HAS A MASS OF 160 kg. TH OF SPRINGS ON

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.8.6P

See similar textbooks

Similar questions

solve, show all steps and fbd. do not provide copied answer or I will report Do problem 12 -22 using double integration. Also find how much additional deflection is added (to the max) if we account for the beam self-weight. Find this additional deflection using the table in appendix C. mechanics of materials chapter 12 (integration of moment)= theta, and integration of theta = v
Valne Parameter Whmade Shear Stress o Spring wire Modulus e ngidity e.SRing Smng Coil haanal chometes Deflection of Spring at allowable Shoar Stress Factor of Safe Wahl's shear Stress factor 800MPA 9AKN/mmf Wire 25mm 15mm K= HC-1+0:615 4C-4 Using he hafurmaton m table 1, desana helical Compresion Spring by detemindng; 9) Allowable Axial loudw turns n' of b) Actve number
This is part of alarger super position problem and I was able to solve for a moment and a concentrated load but this distributed load is confusing me. E = 200 GPa I = 216*10^6 mm^4 w = 81 kN/m d = 1.5 m I ended up getting an answer near -12 mm of diflection but that is an incorrect according to the grader. What would the equation for the elastic curve of this problem be? What is its value at point B? thank you so much!
B/ A steel robotic arm carries a payload of (444.82 kg) has a dimension of (1.524 m) length, (0.1524 m) height and of (0.102 m) breadth. The steel Young's modulus, (E= 206.85GPA) and density of (p=7.87 kgm'). Find the robotic arm deflection.
A rigid weightless be am SUPPorted at the point D by the pixed goint loo ded by the momend M is Support and points B and c holding the beam horisonta lly . a + the ver tical bs connected are For the data listed below determne ! Data > E = 2.1x10$ MPa gie ld stres 6y: 250 MPa , foctor oc Sofety Sr-1.S * Necessoy are a wetion A ? Of Cross - Other Data ; I 5 cM , a : U cm Ma SONM Safety · design method ond limit-state- mordatory. * Use both, Factorr design netled. Both net hats A.E 2A a
The material is a spring wire has a shear modulus of 1.2 x 107 lbf/in2. The maximum allowable stress under design conditions is 50,000 lbf/in2. The spring index is 7. Assume the maximum stress is experienced when a 700 lbm objects falls from a height of 46 in above the tip of the spring, impacts squarely on the spring, and deflects the spring 10 in. Determie: 1. The minimum wire diameter is most nearly A. 0.58 in B. 0.88 in C. 1.4 in D. 1.8 in 2. The mean coil diameter is most nearly A. 8.6 in B. 10 in C. 13 in D. 16 in 3. The number of active coils is most nearly A. 8 B. 11 C. 12 D. 14
A homogeneo us 4o kg vigid block is suspended by three spring whose lower ends were oviginally at the same level Each steel spring has 30 tums •f meau diametu of loo mm 8 mm diameter wive on a G= 83 GN/m?.The bvonze spring has uo tuvns mean diameter of of 15 mm diameter wive on 120mm G=42 GN /m? Compute the maximun and sheaving stress in each spring Phosphor Bronze Steel Steel 1 m 2 m wwww
Department Answer Sheet Name: Date: Course: Time: 2. A Rigid beam with negligqible mass is pinned at one end and supported by two ROds, The beam 20as initially hORIZOntal before the load as appied Find the ertical moyement of P 4 PIS 120 KN Pis Steel Atuminum 4m 3m 3m 2m. im p=120 kN Alumınum A=900 mm² E = 70 GPa Steel A= 600mm? E 200 GPa
natsApp Classes ses This course EHide blocks A rigid beam is supported by a pin at A and two metallic wires at B and C. Determine the force P that causes the point C to displace downward by 0.3 mm. Given: E (wire B) = 70 Gpa, E (wire C) = 200 Gpa and both wires have a diameter D = 4 mm. Consider a linear elastic behavior. P. 2 m 1.5 m A 2 m 2 m 3 m Select one: 10:51 PM A S 0) ENG 4/15/2021
Three extension springs are hooked in series and supports a weight of 70 kg. One spring has a rate of 0.209 kg ∕mm and the other two have equal spring rate of 0.643 kg ∕mm. Find the deflection.
Part D - Present the equations of motion for the system, including the rate of change of deflection. Make sure to simplify your equations as much as possible.
Clear my choice Question 28 Compression coil spring is subjected to load of 500 N is having the mean diameter of 65 mm, wire diameter of 6 mm, number of active coil is 18. Find the shear stress without curvature? Select one: 2. O a. 867 N/mm O b. 400.81 N/mm O C. 481.6 N/mm O d. 563.56 N/mm hp