The spoiler, shown in figure 1, will be fitted at the back end of a stock car to give it downforce on the track. The pressure distribution and average shear stress on the top surface are given and the data on the bottom surface can be neglected. The car can reach a maximum speed of 270 km/h on the track. The spoiler has a length and a width of 1.2 m and 0.3 m, respectively. The density of the air is 1.2 kg/m². Calculate the lift and drag coefficients of the spoiler. Tave = 500 N/m2 P=1.5 kN/m² P=0.15 kN/m? U 12 Figure 1

The spoiler, shown in figure 1, will be fitted at the back end of a stock car to give it downforce on the track. The pressure distribution and average shear stress on the top surface are given and the data on the bottom surface can be neglected. The car can reach a maximum speed of 270 km/h on the track. The spoiler has a length and a width of 1.2 m and 0.3 m, respectively. The density of the air is 1.2 kg/m². Calculate the lift and drag coefficients of the spoiler. Tave = 500 N/m2 P=1.5 kN/m² P=0.15 kN/m? U 12 Figure 1

Name: The spoiler, shown in figure 1, will be fitted at the back end of a s
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: The spoiler, shown in figure 1, will be fitted at the back end of a stock car to give itdownforce on the track. The pressure distribution and average shear stress on the topsurface are given and the data on the bottom surface can be neglected. The c

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Consider an airplane flying with a velocity of 60 ft/s at a standard sea level conditions. At a point on the wing, the airflow velocity is 70 ft/s. Calculate the pressure at this point.
Air at a temperature of 15°C and a pressure of 1 Atm at a speed of 100 km / h figure below-a da it crashes into the visible water tower. Free at Figure-b to prevent Tower toppling as seen in the object diagram, the moment(M)that the base of the tower must resist calculate. The resistance coefficient for the cylinder part is 0.7, the resistance coefficient for the sphere part is 0.3 you may take.
The surface tensions of mercury and water at 60 degrees Celcius are 0.47N/m and 0.0662 N/m, respectively. What capillary height changes will occur in these two fluids when they are in contact with air in a glass tube of radius 0.30mm? Use θ = 130° for mercury, and 0° for water; y = 132.3 kN/m3 for mercury and 9.650 kN/m3 for water. Provide the given along with its solution. (Please write legibly, I did not understand the first solution.)
A pilot flies at 850 mb level over a region with reported sea-level pressure of 1000 mb and temperature of 0 degrees celcius, and temperature decreases with height at 6.5 degrees celcius/km over the region, calculate the altitude of the airplane. Show the derivation of the altitude formular starting from hydrostatic balance.
Compute the final velocity off car U=6 m/s a=9.55 m/s2 t=4 s
With free body diagram please thank you. Clear and complete solution please. 3. A shaft 70 mm in diameter is being pushed at a speed of 400 mm/s through a bearing sleeve 70.2 mm in diameter and 250 mm long. The clearance, assumed uniform, is filled with oil at 20°C with v = 0.005m²/ s and sp. gr .=0.9 Find the force exerted by the oil in the shaft.
B2 is flying at an altitude of 43,000 ft and a speed of 400 KTAS under standard atmospheric conditions. If the average aerodynamic chord is 39,6 ft, calculate the Reynolds number and the average % aerodynamic chord present on the wing
A thin plate is pulled at a speed V through a small gap of hieht h as shown in figure below. The space on both sides of the plate contains different types of fluids. Fixed wall H.H. y Oil ul Plate V (m/s) Oil µ2 Fixed wall Prove that the postion of the plate y takes the form: i. y= (H, +H2) When the shear forces are equal on the both sides of the palte. ii. y = When the drage force is minimum.
3. Air is flowing parallel to the plate at U.-5 m/s and T=300 K over the flat plate of length L=0.1 m and depth of 1 m into the paper, at the atmospheric pressure at the same temperature as the plate. Find; a) Boundary layer thickness at the point x = L of the plate b) Find the total resistance force acting on the two surfaces of the plate. c) The velocities in the hydrodynamic boundary layer are measured by a hot wire anomemeter. The velocity at x=0.1 m on the x component is measured as u=3 m/s. Find the distance from the plate and the y component of velocity v.
fluid mechanics Question 3- The hot air balloon A hot air balloon is stationary about 3 m above the ground when a gust of wind suddenly arrives with a speed of 40 km/h. Determine the horizontal initial acceleration. The balloon is designed as a sphere with a diameter of 10 m. It is filled with 80°C air. Ambient air has a temperature of 10°C. The actual fabric balloon and basket with cargo has a mass of 200 kg.