I need the answer quickly The specific name for the AC-to-DC converter is:DC Chopper1А.В.RectifierС.InverterD.Controller2The SCR turns OFF when its current reduces below.. for sufficient time.A.The reverse current, IRВ.The holding current, IHThe latching current, ILThe gate current, IGС.D.A pure DC quantity a ripple factor of:A.141.4%В.70.7%С.1D.4"A diode of 600V voltage rating" meansA.The peak reverse voltage is 600V.В.The maximum average voltage is 600V.C.The peak forward voltage is 600V.D.The maximum RMS voltage is 600V.The following device is available with highest voltage and current ratingsА.Shottkey diodeВ.SCRC.IGBTD.BJT6The following power switching device is controlled by voltage signal:A.BJTВ.GTOС.SCRD.MOSFET7A converter operated in fourth quadrant if:vo negative and io positivevo and io are negativevo is positive and io is negativevo and io are positiveGiven V1,dc=175V, and V2,dc=75V; then (V1+V2)dc=Could be 250V or 100VА.B.C.D.8A.В.250VС.Impossible to calculate from the information given.D.190.39VThe following parameter determines the quality of inverter output:A.The ripple factorВ.The form factorС.The total harmonic distortionD.The power factor10Given V1,dc= -12V, and V1,ac%3D16V; the RMS of V1=A.28VВ.10.58VС.4VD.20V

1) To connect AC to DC we use rectifier. Ans. Rectifier.

The specific name for the AC-to-DC converter is: А. DC Chopper В. Rectifier С. Inverter D. Controller 2 The SCR turns OFF when its current reduces below. for sufficient time. A. The reverse current, IR В. The holding current, IH С. The latching current, IL D. The gate current, IG 3 A pure DC quantity a ripple factor of: A. 141.4% В. 70.7% с. 1 D.

The specific name for the AC-to-DC converter is: А. DC Chopper В. Rectifier С. Inverter D. Controller 2 The SCR turns OFF when its current reduces below. for sufficient time. A. The reverse current, IR В. The holding current, IH С. The latching current, IL D. The gate current, IG 3 A pure DC quantity a ripple factor of: A. 141.4% В. 70.7% с. 1 D.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

COLUMN A COLUMN B A copper wiring containing 8 color-coded 1. conductors or 4 twisted pairs that offers greater bandwidth for local area networks. A. LEGEND 2. distribution device. A wiring pattern that connects to a central B. HOMERUN 3. Another term for an 8-pin modular jack. C. OVERCURRENT 4. A coaxial cable quad shielded with all copper center conductor used for cable TV. D. INSULATOR It is the maximum current that a conductor can 5. carry without exceeding its temperature rating. E. SHORT CIRCUIT 6. A wiring job where many cables enter a device or a junction box that is considered an unsafe practice in electrical wiring, F. CIRCUIT BREAKER 7. An electrical safety device designed to protect an electrical circuit from damage. G. ARC FLASH 8. unintended path with very low resistance. Occurs when an electrical current flows in an H. AMPACITY 9. amperage capacity of the circuit. Occurs when the current exceeds the rated I. UTP 10. A method of extending an electrical wire to the ground…
The is the distance from-1 the centre of one slot to the centre of .the next slot a) coil span O b) pole pitch O c) slot pitch O
Question.
What is the total number of systems?
3. Which of the following statements about the use of structural steel as an equipment grounding conductor(EGC) in an AC system is correct?A. Structural steel isn't allowed for use as an EGC.B. Structural steel can be used as an EGC bonding jumper between panelboards.C. Structural steel must have an EGC bonding jumper every three feet of structure.D. Structural steel can be used as an EGC when it's bonded at both ends.
I need the answer as soon as possible
Question Completion Status: Click Submit to complete this assessment. Question 8 What do you do to an asynchronous counter to let it count froms14 to 0? (Handwriting solution is needed: include this in your pdf file) Click Submit to complete this asseESment,
Estimate the length of conduit to perform the next bends. EMT will be bend using a hand bender. Provide your answer in inches (just the number) using up to 2 decimals. The picture shows two panels connected by a back-to-back 23.5" stubs EMT 3/4" 6.25 ft P
The contractor is controlled by?
Assuming all terminals are rated 75°C and you have a #10 AWG THHN/THWN conductors in a conduit and the conduit is run on the roof off a office building where the ambient temperature never rises above 30°C the largest size circuit breaker or fuse permitted to protect these wires is:?
The wording that I am running into with questions such as "The number of conductors required to be installed between three-way and four-way switches is " is confusing. The text is not expalining this in a way that I am understanding anything other than grounding conductor, which is optional unless I am using a metal box. So what type of "conductor" is beng discussed?
Complete the following text with words Pt100 sensors are a specific type of _____(1) detector. The most important characteristic of Pt100 elements is that they are made of _____(2) with an electrical resistance of _____(3) ohms at a temperature of ______(4) °C and temperature coefficient ____(5). It is by far the most common type of RTD sensor. The other materials with which RTDs are built are: ___(6), _____(7), ______(8). The most recommended conditioning method is reading at _____(9). Typically, a _____(10) behavior of the Resistance-Temperature relationship can be assumed.