The solids from a dilute slurry are to be separated using hydrocyclones. The density of the solids is 2900 kg/m3 , and liquid is water. A recovery of 95 per cent of particles greater than 100 /Am is required. The minimum operating temperature will be 10 °C and the maximum 30 °C. Design a hydrocyclone system to handle 1200 1/m of this slurry.

Q: Briefly Explain the factors that affecting evaporation?

A:

Q: Answer Group (A) Group (B) 1. Solubility Hand hydrometer. 2. Preservation process by salt A surface…

A: A table contains two groups (group A and group B). The points mentioned in group A are to be matched…

Q: discussion Heat transfer by natural and forced convection .

A:

Q: (B):-During corrosion tests, current density of 0.86 Amp/m² sample immersed in sea water.

A:

Q: Powdered milk can be produced from liquid milk in a three-stage process: (1) vacuum evaporation in a…

A: The reason for three-stage process is preferable to a single stage process involving just spray…

Q: With an aid of a diagram, compare between FOUR (4) ideal gas flow patterns in a membrane separator

A: ideally there are four different flow patterns for membrane separation process:1)complete…

Q: The weight of a clean sand core sample in the air is 27.76g. When saturated with kerosene, it…

A: Given data:  The weight of a clean sand core sample in the air (Wsand )= 27.76g When the core sample…

Q: About precipitation and dispersion hardening, answer: (a) Explain what the precipitation process…

A: Dear Subscriber! The three questions posted here require independent analysis/calculations. As per…

Q: Determine the terminal settling velocity of a coal particle of size 400 micron in water at 20 oC by…

A: We need to find settling velocity of coal particle water and then we need to compare it with…

Q: 5. Physical properties of the formation crude oil includes volume coefficient and viscosity.

A: The physical properties of crude oil vary according to its composition, the relative abundance of…

Q: 7. What the type of calculated permeability in Permeability of Liquid method ?

A: Permeability of the material is defined as capacity of that material of transmitting or passing…

Q: Q3// A plate and frame press gave a total of 0.001 m' of filtrate in 14s and 0.005 m in 160s. The…

A: Given that, The volume of the filtrate obtained in time t1 = 14 s is V1 = 0.001 m3 The volume of the…

Q: 800 kg of a porous material containing 0.38 kg H2O/kg wet material is dried in a tray dryer such…

A: Total weight of porous material Wt = 800kg Initial fraction of H2O = 0.38 kg H2O/kg wet material…

Q: A batch of porous solids B are dried from 50% to 30% moisture under constant drying conditions.…

A:

Q: Calculat surrounding Calculate th covered with much heat w

A:

Q: What are the assumptions made for mass transfer in the packed column?

A: Packed column is a distillation column that has packings in some sort of arrangement or in disorder.…

Q: amount of energy released

A:

Q: A container of gas is being cooled. Identify the physical change occurring during the time interval,…

A: The process that is taking place between the time interval of 4 mins to 9 mins is to be chosen.

Q: A steel coupon with an anode surface area of 1000 cm2 is placed in an electrolyte. The corrosion…

A: As the  metals are found in the ores present naturally in the environment. The corrosion process can…

Q: What is the difference between the Van Everdingen and Hurst unsteady state and Carter-Tracy unsteady…

A: Water influx is explained as the incursion of water into oil or gas bearing formations. In simple…

Q: Which of the followings is the reverse of melting? Select one: O a. Sublimation O b. Solidifying O…

A: we have to select the correct options , which implies the reverse of melting. we know that  Melting:…

Q: The process of crystallization is done in which way: A. Solvent vaporizes B. Dissolution of solution…

A: Crystallisation is the process by which a solid forms, where the atoms or molecules are highly…

Q: A solution is made by putting 100 g of NaNO3 into 200 mL of water at 70 degrees C.If the solution…

A: Answer Salt precipitates out is NIL A solution is made by putting 100 g of NaNO3 into 200 mL of…

Q: Define the following in chemical engineering perspective and draw an arrow block diagram of the…

A:

Q: (c)  Convert g of solute and solvent to moles, and find the ratios of    each part to the total.

A:

Q: Please discuss "Drilling problems related to drilling fluid rheological property"

A: Drilling muds or fluid is sued as carrier of rocks produced during the oil and gas drilling…

Q: Plate filter press is commonly used in industry due to its high strength, long service life and good…

A: tbatch = 60 min = 1 hr tdischarge + tcleaning = 10 min tfilteration = tcleaning = 10 min…

Q: explain the problems that may arise in the process

A:

Q: Q/ explain about effect wettability on 1- Saturation 2- Porosity 3- Relative permeability 4-…

A: To Explain The effect of wettability on saturation, porosity, relative permeability and capillary…

Q: During a carburization process for the surface treatment of steel, how much processing time in…

A: Given: Initial carbon content (C₀) = 0.4% Desired carbon content (Cₑ) = 0.85% Carbon content at the…

Q: n SPME for HPLC, analytes are desorbed from the fiber into solvent that is injected into the HPLC…

A: SPME also known as Solid Phase Micro Extraction is an equilibrium sampling method and can be used…

Q: Describe and explain direct solar radiation on surface.

A: Since you have posted multiple independent questions in the same request, we will solve the first…

Q: A plate and frame filter press is used to filter a compressible sludge (S = 0.45) at 50 psia for 2…

A: Given :Sludge compressibility Filtration pressure Filtration time Washing pressure Wash water volume…

Q: In ceramic industry, the removal of moisture in ceramic mixture is done through drying. If the feed…

A: Given Data  The amount of moisture in feed =0.50The moisture upto which the drying should be done =…

Q: Give practical applications of the concept of the surface phenomena. What is the importance of this…

A: Dear user! As per our authoring guidelines, we have answered the first of the multiple questions…