The slotted guides in the figure act according to the relations x = 16 - 12t + 4t ^ 2 and y = 2 + 15t - 3t ^ 2. Here x and y are in millimeters and t is in seconds. Find the tangential and normal component of the acceleration of the pin "P" and its directions at time t = 2 s

The slotted guides in the figure act according to the relations x = 16 - 12t + 4t ^ 2 and y = 2 + 15t - 3t ^ 2. Here x and y are in millimeters and t is in seconds. Find the tangential and normal component of the acceleration of the pin "P" and its directions at time t = 2 s

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

P
n the expression below, i, j, and k are mutually perpendicular unit vectors having directions fixed in a frame of reference. Vector vP is the velocity of point P moving in the frame; t is the time measured in seconds. Determine the acceleration aP at time t = 2 s for the velocity expression given.
The T shaped plate is rotating at a rate of w = 10 rad/s CCW (as shown) and deccelerating at a rate of a = -2.5 rad/s². The relevant dimensions of the plate are a = 3 in and b = 2 in. The plate is inclined at an angle = 15 deg at the instant shown. 1. What are the inertial velocity and acceleration vectors of points P and Q in terms of the unit vectors 6₁ and 6₂? 2. Which point has a greater velocity magnitude? acceleration magnitude? 3. How much of the acceleration is due to the Coriolis effect? 4. How many revolutions will the plate complete before reaching zero angular velocity? iz a b₂ 9 ......... b Q a
2.
F 2 3 m3,JS3 M3 D 1 S3 B Ф1 w=const A - 0 Using graphical method draw: - velocity vectors in point S3 - acceleration vectors in point S3
3 Problem A hydraulic cylinder rotates around point O at a constant rate 60 deg/s and the cylinder length L is decreasing at a constant rate L = -150 mm/s. Determine the magnitude of velocity and acceleration of the endpoint B when L = 125 mm. Assume that d = 375 mm. d 0 B
2. The gear A on the drive shaft of an outboard motor has a radius of ½ inch while the meshed pinion gear on B has a radius of 1% inches. If the drive starts from rest and is accelerated at a constant a = 200 rad/s², what is the speed, tangential acceleration, and normal acceleration at point P on the propeller after 3 seconds. 2.20 in
Solve this by Velocity and Acceleration Analysis. Also show the velocity and acceleration polygons
In the figure, link 2 rotates with constant annular velocity CO2. A slider link 3 moves outwards with a constant relative velocity where Q is a Point on slider 3 and P is a point on link 2. The magnitude and direction of Coriolis component of acceleration is given by Q on 3 VOP 002 -P on 2
A cylinder of radius 7 = 0.2 m is about to start rolling down an inclined plane. The acceleration of the center of the cylinder is 9.81 sin(0) m/s?. The angular acceleration is 9.81 sin(0)/r rad/s?. Assume 0 = 0.8 rad. What is the magnitude of acceleration of the point on the cylinder furthest from the inclined plane in m/s?. Hint: Since it is about to start rolling, the velocity of the center of the cylinder and angular velocity of the cylinder are still zero at that instant. You Answered 0.2739 Correct Answer 14.075 margin of error +/- 2%
The figure shows a rigid link AB of length 2 m which rotates anticlockwise about a fixed point at A at a rate of 2 rad/s, but which is decelerating in its rotation at 1 rad/s². At the instance of time shown in the diagram, with the link AB at 60 degrees to the horizontal, what is the y-component of the absolute acceleration of point B? (The positive sense of the x and y directions are given by the axes in the diagram). O O O O O w = 2 rad/s a = -1 rad/s² 7.93 m/s2 Don't Know -7.93 m/s² 5.93 m/s2 -5.93 m/s² B 60⁰
In the system on the picture the bigger wheel is not moving, the smaller wheel is connected to the center of the bigger wheel with the rod and it can rotate around the bigger wheel. the smaller wheel starts its movement with angular acceleration ε=10rad/s^2. find the acceleration of point B (marked in a drawing) after 1 full rotation. The radius of the bigger wheel is equal to 0,3m. The radius of the smaller wheel is equal to 0,1m.