The slotted arm OA rotates about a horizontal axis through point O. The 0.30-kg slider P moves with negligible friction in the slot and is controlled by the inextensible cable BP. For the instant under consideration, 0 = 20°, w = 0 = 5.5 rad/s, 0 = 0, and r = 0.60 m. Determine the corresponding values of the tension T in cable BP and the force reaction R perpendicular to the slot. The force R is positive if the contact comes from the lower edge of the slot and negative if the contact comes from the top edge. T= @ R= r = 0.60 m Answers: 0.40 m- i i B P N N

The slotted arm OA rotates about a horizontal axis through point O. The 0.30-kg slider P moves with negligible friction in the slot and is controlled by the inextensible cable BP. For the instant under consideration, 0 = 20°, w = 0 = 5.5 rad/s, 0 = 0, and r = 0.60 m. Determine the corresponding values of the tension T in cable BP and the force reaction R perpendicular to the slot. The force R is positive if the contact comes from the lower edge of the slot and negative if the contact comes from the top edge. T= @ R= r = 0.60 m Answers: 0.40 m- i i B P N N

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The uniform 99-lb log is supported by the two cables and used as a battering ram. If the log is released from rest in the position shown, calculate the initial tension induced in each cable immediately after release and the corresponding angular acceleration a of the cables. Assume a = 3.9 ft, b = 2.9 ft, c = 1.3 ft, e = 61°. a a C Answers: TA = i 21.6 Ib TB = i 64.9 Ib a = 4.00 rad/sec?
The spring-mounted 0.62-kg collar A oscillates along the horizontal rod, which is rotating at the constant angular rate ở = 6.3 rad/s. At a certain instant, ris increasing at the rate of 630 mm/s. If the coefficient of kinetic friction between the collar and the rod is 0.46, calculate the friction force F exerted by the rod on the collar at this instant. Vertical Answer: F = i N
The robot arm is elevating and extending simultaneously. At a given instant, 0 = 34°,0 = 37 deg/s, 0 = 107 deg/s²,1 = 0.55 m, i = 0.37 m/s, and 7 = -0.36 m/s². Compute the radial and transverse forces F, and F that the arm must exert on the gripped part P, which has a mass of m = 20.8 kg. Compare with the case of static equilibrium in the same position. Assume d = 0.52 m. SASAARE Answers: Dynamic: Fr= Static: i i N, Fe= i N₁, Fe= i Z Z N N
3. Two blocks are connected by a massless string horizontally. The left block is pulled by a 100N force 30° above horizontal as shown in the figure. Assume the coefficient of kinetic friction between the blocks and the supporting surface is 0.15. (a) Show all the forces acting on each block by drawing its free body diagram. Determine (b) the tension T of the string connecting the blocks and (c) the acceleration a of the blocks. F = 100N 30° 100N T 200N Pk=0.15
B
H3
The system shown below is released from rest. The static and kinetic coefficients of friction between slider A and the rail are 0.8 and 0.2, respectively. Consider massless-frictionless pulleys and massless cable. Mass of slider B is 15 kg and force P= 25 Newtons is always acting on it. If the acceleration of slider B during the motion is 5 m to the right, determine the tension developed in the cable in Newtons. Consider g =10 m.
The slotted arm OA rotates about a horizontal axis through point O. The 0.18-kg slider P moves with negligible friction in the slot and is controlled by the inextensible cable BP. For the instant under consideration, θ=26∘, ω=θ˙=4.6 rad/s, θ¨=0, and r=0.63 m. Determine the corresponding values of the tension T in cable BP and the force reaction R perpendicular to the slot. The force R is positive if the contact comes from the lower edge of the slot and negative if the contact comes from the top edge. I found R to be equal to 1.05 which is correct, I can't find T.
The strings AB and AC connect the 200 g ball to the vertical shaft, as shown in Fig. 2. The shaft rotates at a constant angular speed w and the ball travels in a horizontal circle with the strings inclined at a = 30° to the shaft. Given that the tension in string AC is 4 N. Draw a free body diagram of the forces on the ball. Calculate the radial acceleration of the ball. Find the value of the angular speed w. What is the tangential acceleration of the ball? Page 1 of 2 200-g A Fig. 2 /400 mm 400 mm
The body A with a mass of 50 kg is in equilibrium with the help of the pulling force generated in the AB and AC cables in the middle of the inclined plane and the friction force between the curved surface and the object. The friction force is on the line of motion of body A and develops in the opposite direction to the movement in the direction of the arrow shown in the drawing. Since the pulling force in AB and AC cables is 15.1 and 22.1 N, respectively, calculate the balancer friction force acting on the object vectorially? (g = 9.81 m / s'2)
Please provide fbd with tension (and direction of tension) and kinetic diagram with assumed direction of weight
Dynamics