The slotted arm OA forces the small pin to move in the fixed spiral guide defined by r = KO where is measured in radians and the constant K = 3.8 m. Arm OA starts from rest at 0 = 53° and has a constant counterclockwise angular acceleration = 2.9 rad/s². Determine the magnitude a of the acceleration of the pin P when 8 = 129⁰. Answer: a = i m/s²

The slotted arm OA forces the small pin to move in the fixed spiral guide defined by r = KO where is measured in radians and the constant K = 3.8 m. Arm OA starts from rest at 0 = 53° and has a constant counterclockwise angular acceleration = 2.9 rad/s². Determine the magnitude a of the acceleration of the pin P when 8 = 129⁰. Answer: a = i m/s²

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Q3: For the beam shown in Figure (3), given INA = 1.- 10 mm", calculate the transverse shearing stress at points A, C and G on the section at the left support of the beam. w=10 kN/m 4 m Figure (3) in Q3 ΝΑ 29 mm 10 mm 50 mm G C ΔΑ 8 mm 25 mm 50 mm 8 num
3. The rod OB rotates counterclockwise about O at the constant angular speed of 30 rev/min while the collar A slides toward B with the constant speed 3 ft/s, measured relative to the rod. When the collar A is in the position R=0.6 ft, 0= 20°. Find the acceleration of the collar at this point. (25) x
1. The structure shown in the figure has a motor on the top of the column. When the motor rotates, try to find the maximum horizontal displacement and the amplitude of the column end bending moment. It is known that the weight of the motor and the structure is concentrated on the top of the column, W=20KN, the amplitude of the horizontal centrifugal force of the motor FP-250N, the motor speed n=550r/min, the linear stiffness of the column i=EI,/h=5.88*10$N•cm Fp(t)=Fpcos Ot I→∞ EI El h=6 m
B8
A and B, weighing 8N and 10N respectively, are connected by a weightless cord passing over a frictionless pulley and resting on the smooth plane as shown. Determine the angle 0 that defines the position of equilibrium. B 45
Q1: Determine the Moment of the Force 800N shown in Fig. about point O By at least 3 ways. 875 mm- 625 mm 30° F= 800 N *** *
The ends of a 0.25kg rod AB are constrained to move along slots cut in a vertical plate as shown. A spring of constant k=3N/m. is attached to end A in such a way that its tension is zero when θ=0°. the rod is released from rest when θ=45° (position 1) until it reaches θ=0° (position 2). (L = 25 m) Determine the velocity at point b.
23
Problem 2. For the beam shown, choose the spring force as the redundant reaction. The modulus is E = 30 x 106 psi. Determine: a) The support reaction at the base of the spring, b) the rotation of the beam at the left support. 5000 lb/in. R₁ 500 lb/ft -20 .2 m 2² 4"
For the frame shown in TOS-004, if E = 200 GPa and I = 500 x 10^6 mm^4 calculate the vertical displacement at joint B. EI is constant.
Handwritten answers pls.
18,8:Find the force P that the wooden column shown in the figure can support with a confidence of n=3. E=10 GPa, λp=60. Answer: t=0,46 cm