The sliders A and B are connected by a light rigid bar and move with negligible friction in the slots, both of which lie in a vertical plane. For the position shown, the hydraulic cylinder imparts a velocity and acceleration to slider A of 0.4 m/s and 2 m/s?, respectively, both to the right. Determine the acceleration of slider B and the force in the 3 kg 05 m 60 bar at this instant. Fig.P2

The sliders A and B are connected by a light rigid bar and move with negligible friction in the slots, both of which lie in a vertical plane. For the position shown, the hydraulic cylinder imparts a velocity and acceleration to slider A of 0.4 m/s and 2 m/s?, respectively, both to the right. Determine the acceleration of slider B and the force in the 3 kg 05 m 60 bar at this instant. Fig.P2

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Rod OA rotates counterclockwise with an angular position - 2t rad, where t is in seconds. The double collar B is pin-connected together such that one collar slides over the rotating rod and the other collar slides over the circular hoop rod described by the equation r = 1.6cose m. If the total mass of both collars is 0.5 kg and of the rod and hoop are negligible, when = 30° which takes t = ()(180) sec, determine the circumferential acceleration of the collars, ag. [m/s2] (sign sensitive) 6=ki 16 cos 8.
(a) the relative acceleration of the collar with respect to the rod, . (b) the magnitude of the horizontal force exerted on the collar by the rod.
Pin B weighs 0.1kg and is free to slide in a horizontal plane along therotating arm OC and along the circular slot DE of radius b=500mm.Neglecting friction and assuming that θ= 15 rad/s andθ=250 rad/s2 for the position θ= 20o , determine for that position(a) the radial and transverse components of the resultant forceexerted on pin B, (b) the forces P and Q exerted on pin B,respectively, by rod OC and the wall of slot DE.
IV. For the following system that starts from rest, the spool has a weight of 300 N and a radius of gyration ke = 0.3 m, and block A is attached to it as shown of weight 200 N. A constant horizontal force F is applied to the cord in order to give the block an upward speed of 5 m/s. (Neglect mass of cord and tension force). -F 1. Draw the free body diagram of the system. 2. Calculate the angular speed of the spool at t= 6 seconds. 3. Calculate the vertical reaction force at the pin at t= 6 seconds. 4. Calculate the horizontal force F.
A uniform rod BC of mass 10 kg is connected to a collar A by a 350-mm cord AB. Neglecting the mass of the collar and cord, determine (a) the smallest constant acceleration a for which the cord and the rod will lie in a straight line, (b) the corresponding tension in the cord. Hint: The smallest constant acceleration is attained when point C of the rod is about to leave the floor. ад A 350 mm 650 mm C B 450 mm
A rectangular block of mass m is on top of a wedge-shaped block of mass M and angle θ, as shown below. All contact surfaces are frictionless. A horizontal force of magnitude F is applied to the wedge such that the rectangular block moves with the wedge and does not slide. (a) Draw free-body diagrams for each block separately in code. Indicate the direction of the acceleration for each block. Identify the forces on these diagrams that are Newton's third-law force pairs. (b) Find the magnitude of F in terms of m, M, g, and θ
Knowing that the coefficient of static friction between the tires and the road is 0.80 for the car as shown in figure 2. At this car, suddenly brakes are applied when it was moving with velocity of 360 inch/sec and it skidded to rest in 240 inch. Determine the magnitude of the normal reaction and of the friction force in the terms of W(weight) at each wheel as the car skidded to rest. { Use m=w/g, for the mass of the car if required, where g=386.09inch/s2.}
Please label steps clearly
A 50 Ib block A is attached to a wire that is wrapped around the shown flywheel of 30" radius and I = 12 ft-lb-s². The system is released from the rest. Neglect the effect of friction, determine (a) the acceleration of the block A, (b) the speed of the block A after it has moved 10 ft. A
EXERCISE 2.53 Collar C is pushed along the guide bar defined by y= 2(1-0.25x²), where x and y have units of meters. The angular speed of arm AB that actuates the motion is the constant value = 20 rad/s, so = ct. Determine the forces exerted on the collar by arm AB and the guide bar at x = 1 m. The mass of the collar is 2 kg, and gravitational effects are ignorable. (Hint: use Cartesian and polar coordinates to solve the problem.)
An object of mass m1 slides on a sloped block of mass M2, which in turn slides on a horizontal surface. The slope angle is a constant 3, and both masses are initially at rest. There is no friction between any of the objects, and the masses are subject to the force of gravity -mgêy. Use as co- ordinates the horizontal position x2 of mass m2, and the height y1 of mass m1, as shown in the y4 Y1 M2 x2 diagram to the right. Find the equation of motion of block 2, ä2(t). The expression should only include expressions involving constants: M2, m1, g, and B.