The sketch of a traverse done in a field is shown in the figure together with the measured distances and bearings of each line segments. Adjust the distances and bearings of each line using compass rule and transit rule.

The sketch of a traverse done in a field is shown in the figure together with the measured distances and bearings of each line segments. Adjust the distances and bearings of each line using compass rule and transit rule.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 45 1b 1. Determine the vector representation of the couple 60° 3 ft shown; A y 1.8 ft B 60° 45 1b

Q: 2. Using the information below, determine the following: a. Sketch of the traverse and label…

Q: The following bearings were observed in a close traverse. Find the included angles and correct the…

A: When the bearing is correct the difference between the fore bearing and back bearing is exactly the…

Q: FS 2.875 m 4.252 m 5.478 m 6.142 m BS ТР 1 ТР 2 4.325 m 9.542 m 9.631 m 8.133 m BM 1 Elev. = 56.287…

A: GIVEN Traverse Illustration To Determine HI, Elevation, Correction to be applied, and Corrected…

Q: Line Bearing N60°E Distances АВ 1000 m BC Due South CA N60°W

Q: Using DEPENDENT MOTION ANALYSIS, what is the length equation? Draw the reference line

Q: Traverse) and Recorded the following results, the length and deflection angle of each line: AB=…

Q: Surveying question: In the quadrilateral ABCD, the following angles are measured; Angle BCD = 33…

A: Given- Angle BCD = 33 Angle ADC = 34.5 Angle ACB = 49.5 Angle ADB = 37.5

Q: help me plot the horizontal and vertical distance using free hand

Q: Find the degree of curvature of using arc definition of: Answer format DD mm ss. for 10°11'12" - 10…

A: Radius of different curves are given. We need to calculate degree of curvarure by arc defination.

Q: A surveyor uses an auto-level instrument to calculate the length of the sides of a traverse…

A: The formula to calculate the horizontal distance is given by, D=KS+C Here, K is the multiplying…

Q: Line Length Bearing meter S 80° 46' W N 40° 00' W АВ 550.63 ВС 295.08 CD 610.19 Unknown DE 886.17 S…

A: As the length and the bearing of the lines are given: Calculating the missing bearings of CD and GA.

Q: What are the derived formulas used in simple surveying curves, compound surveying curves, reverse…

A: Given: The types of curves are mentioned as: Simple surveying curves Compound surveying curves…

Q: fundamentals of surveying. CLOSED COMPASS TRAVERSE. Given in the accompanying sketch are the…

A: We have to adjust the observed direction and tabulate accompanying sketch observed forward and back…

Q: Which of the following is not required in compass surveying? O a. Lengths of lines O b. Connecting…

A: Which of the following is not required in compass surveying?a) Lengths of linesb) Connecting linesc)…

Q: Complete the notes, find the elevation of point A and state the error in the network. Determine the…

A: HI= Elevation +BS Elevation= HI-FS

Q: Assume contour interval of 5 m, draw the contour lines based on the given elevations of the points…

A: Contour is drawn below with 5m interval

Q: LINE DISTANCE BEARING AB 60 N15°30'E BC 72.69 S82°23'E CD 44.83 S17°30'E DE 56.45 S70°36'W EA 50…

Q: DISTANCE (m) 607.66 AZIMUTH 86 35' 31°35' 137°10' 240 45' 284 45' UNKNOWN LINE А-В B-C 301.08 677.73…

Q: LATITUDE DEPARTURE AŽIMUTH COURSE LENGTH FROM NORTH +N -S +E o°50' 296 06' 205°54' 135 20' 33 27' 95…

Q: 24: It is required to construct a road with b=10m width and 1:2 side slope. The reduced level the…

A: GIVEN

Q: From the information shown in the following table, find the magnitude of the local attraction line…

A: in the close polygon the part point will be meet with the first point so their is the side FG must…

Q: Q2: Draw the following figure using AutoCAD commands without colors. 60° R24 450 86.5 173 86.5 86.5…

A: Question being asked here to draw the given diagram in AUTO CAD without colours. and for this…

Q: tracing implicit curves

A: Interval analysis is basically a numerical analysis where the calculation is done using real numbers…

Q: Describe about the method Sixty-Degree Approximation.

A: Approximation methods are used to estimate the vertical stresses approximately for preliminary…

Q: ABCD is a traverse. The included angles are measured as angle A = 110 0 angle B = 54, angle C = 125,…

A: A is the origin and AB is the arbitrary meridian Bearing of line AB= 0° BA= 180° BC=180+54° =…

Q: What are longitudinal profiles and transverse profiles? And how can we do each of them manually?

A: Longitudinal profile: the longitudinal profile involves the uplift side along with the route, the…

Q: Determine the linear error for closure, and the adjusted lengths and bearings of the lines in…

A: ADJUSTMENT OF TRAVERSE BY COMPASS RULE Latitude = Lcosθ Departure = Lsinθ (L is length of course and…

Q: C. Stadia Formula: D = (f/i)s + (f+c) Percentage Error: % Error Length Width observed value - actual…

Q: Triangulation is associated with a. Levelling b. Chain surveying c. Compass surveying d. Triangular…

A: Triangulation is associated with with chain surveying. In triangulation whole area is divided into…

Q: The interior angles of a five sided polygon ABCDE are as follows: A = 117 36' , B = 96 32', C = 142…

Q: The following are bearings and distances taken on a closed traverse. PROBLEM 1: Bearing N60°E Due…

A: As per the angles given, the traverse is a equilateral triangle.

Q: Situation 1] A circular road is proposed to be laid out with tangent AB whose bearing is N87054'E…

A: Step 1: Tangent length T = Radius x tan D/2 R = 1720 / 4.5 =382.22 m T = 382.22 x tan(4.5/2) = 15m…

Q: B: Write down all the necessary steps to draw below shape using AutoCAD (Select Any Start Point and…

A: Draw from inner to outer. 1.Select circle tool, click the centre point and type the diameter 50…

Question

The sketch of a traverse done in a field is shown in the figure
together with the measured distances and bearings of each line
segments. Adjust the distances and bearings of each line using
compass rule and transit rule.
S 5459'15" E
382.24
Line
Bearing
Length (ft)
AB
S 68°05'35"W
472.68
BC
N 19°46'00"W
216.13
A
CD
N45°55'20"E
276.52
S 68°05'35" W
472.68
DA
S 54°59'15"E
382.24
N 45°55'20" E
276.52'
N 19°46'00" w
216.13'

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Where X =2
Magnetic Declination: 1. In a compass survey made twenty years ago the observed magnetic bearing of a reference line XY was N 42'21' E when the magnetic declination was 6*25' East. Lately in 2018, a new survey was made and the declination in the same survey site changed to 10'35' West. Determine the following descriptions of line XY: a.) Its true bearing twenty years ago; b.) The true azimuth from North and South; c.) Its new magnetic bearing; and d.) The magnetic azimuth from North and South in 2018.
A closed traverse has the following data: Distance Line Вearing Latitude Departure (m) 1081 S 73°47'E S 15°14'W S 67°07'W АВ ВС 1589 CD 1294 DE 2507 EA 1738 7. Determine the length of the closing line (AD) 8. Determine the bearing of line DE 9. Determine the bearing of line EA 10. Determine the area using DMD or DPD
Calculate: a) the bearing of line CD b) the bearing of Line DE c) the area of the traverse pls answer in COMPLETE, 3 dec places, and provide ILLUSTRATION
Closed compass traverse data (With sketch)
please plot this for surveying!
The following data for a closed traverse is as follows. Determine the area of the closed traverse
A closed traverse has the following data: Line Distance (m) Bearing AB 44.47 BC 137.84 CD 12.83 N 1deg 45min E DE 64.86 N 72deg 10min E EA 107.72 S 48deg 13min E Find the bearing of line AB. O S 37deg 18min W O S35deg 30min W O S 38deg 34min W O S 36deg 26min W
Show complete solu
b)Table 3 shows the data of closed traverse. Table 3 Station Bearing Distance (m)1-2 103o 31' 30” 71.7002-3 196o 26' 50” 73.3003-4 273o 57' 10” 75.2004-5 340o 13' 50” 54.3505-1 55o 18' 40” 54.030 Illustrate a diagram and find; i)The latitude and departure of each line.ii)The adjusted value of latitude and departure for each line. iii)The coordinate for each station, given the coordinate of station1 (N3000, W4000)
Q3: A: Draw the diagram of traverse classification. B: In closed traverse ABCD. The partial coordinates were known as shown below. Determine its area by DMD method. 04 N Dofland OWODY dienstl it with (nm) dinostim Mem. AB BC CD DA ΔΧ 40 -80 -50 AY 60 100 -70
TRANSIT RULE. pls make use of table and draw the traverse