The sinusoidal voltage source in the circuit in (Figure 1) is developing a voltage equal to 50 sin 400t V. Suppose that R= 500N Part A Find the Thévenin voltage with respect to the terminals a,b. Express your answer in volts to three significant figures. Enter your answer in re V ΑΣφ vec| VTh = V Submit Request Answer Figure Part B < 1 of 1> Find the Thévenin impedance with respect to the terminals a,b. Express your answer in ohms to three significant figures. Enter your answer in re Vol AE¢ It vec ? 31.25 uF 400 mH ZTh = Ω Submit Request Answer

Q: What are the steps for plotting points on microstation uisng offset, station, side and elevation?

A: We need to tell about steps for plotting points on microstation uisng offset, station, side and…

Q: Evaluate these complex fractions: 6/30° +j5 - 3 -1+j+2e45° (a) (b) [5+ (15 - j7)(3+j2)*…

A:

Q: List the minimum trade size Type EMT for each of the following applications. (Objective 12-1)…

A: As per Bartleby expert policy only first individual question is to be answered. So, answering only…

Q: Airframe Electrical System Question: What is the recommended shield coverage area for wires and…

A: The recommended shield coverage area for wires and cables that are susceptible to EMI is 85%…

Q: 9.a. What should be done with the connector ferrule once a connector is attached to a fiber optic…

A:

Q: A 75-ohm load terminates a 50-ohm transmission line. The point of reflection is at the load. If the…

A:

Q: Fill in the blanks: Q. Expansion of LSB is

A: A combinational circuit is one in which the various gates in the circuit, such as the encoder,…

Q: Give me about ten examples of electrical code violations in maintenance and repair. Hopefully the…

A: Choose the wrong Circuit breaker There is a need to follow the national electric code. 1. Standard…

Q: Determine the size and type of wire to he installed to a building with temperature that reaches…

A: Here ratings of loads are given for a single phase 230 V source. We need to determine the size and…

Q: 6.a. Extreme _______ may cause some nonmetallic conduits to become brittle and therefore more…

A: 6.a. According to article 352 of NEC  Extreme cold may cause some nonmetallic conduits to become…

Q: 60. A service with copper phase conductors rated al 300 kemil per phase shall have Cu. a minimum…

A: Since you have asked multiple question ,we will slove the first question for you .If you want any…

Q: Part 2: Analysis and selection of the Wind Turbine. The team decides at install a 30 MW wind farm.…

A: 1: Analysis and selection of the Wind Turbine.The team decides to install a 30 MW wind farm. The…

Q: The nominal output voltage of a certain regulator is 8 V. The output changes 214 mV when the input…

A: Given The nominal output voltage of a certain regulator is 8 V. The output changes 214 mV=0.214Vwhen…

Q: In a 10-trunk circuit, there are 180 calls in one hour. The average holding time per call is 2…

A: This is a problem of mobile communication. The detailed solution is given in the next step.

Q: The nominal output voltage of a certain regulator is 8 V. The output changes 214 mV when the input…

A: It is given that: nominal output voltagevo=8 V,change in output voltage∆vo=214 mV,Vi=25 V to 16 V

Q: Please answer in typing format

A: 1_________conductors shall not be used for more than one multiwire branch circuit unless…

Q: Find the value of unknown. 3:1 — 6:____

A: The solution is given below

Q: . The only exception to the need for all information technology equipment to be satisfactorily…

A: Equipment grounding is mainly done for user protection.it is a non-current carrying element. A. In…

Q: And a typical phone service installation, a drywall is constructed beneath the_. A. Weep hole b.…

A: In this question we need to find a a correct option

Q: Fill in the blank: Q: The mathematical formula for obtaining IDTFT is ?[?] =…

A: The inverse Discrete-time Fourier Transform (IDFT) is used for calculating the discrete time domain…

Q: wiring diagram for a single pole switch controlling the top half of a duplex receptacle that when…

A: The objective of this question is to provide a wiring diagram for a specific electrical setup. This…

Q: L1. Boxes are classified by type, construction, and A. installation location. B. luminaire support…

A: 1) Boxes are referred as a electrical boxes are of plastic or metallic, Boxes are used in light…

Q: The Code places a maximum open-circuit voltage on lighting equipment in or on homes. This maximum…

A: The maximum open circuit voltage on lighting equipment in homes are 1000 V.

Q: 3. Determine i1, i, iz and i4. сло iz 2A D+ ЗА Odis Пина 13

A: To calculate currents i1, i2, i3  and i4

Q: When is supernode used in a circuit analysis? Provide an explanation.

A: If we have a voltage source in between two nodes then the two nodes are considered as SUPER NODE

Q: -6 µC A)

A:

Q: Fill in the blanks: Q. Other name of DTE is _______________ Equipment.

A: Data terminal equipment (DTE) is the ultimate tool that converts client data into signals or…

Q: Fill in the blanks: Q. Other name of VDC is _______________ Controller.

A: Transfer function:  The ratio of the Laplace transform of output to the Laplace transform of input…

Q: 2-Calculate the minimum and maximum protection for an A/C, its conductors (75 ºC) and its grounding.…

A: Step 1:    Step 2: Step 3:Step 4:

Q: Write down three situational questions and behavioral questions each to be asked while interviewing…

A: Write down three situational questions and behavioral questions each to be asked while…

Q: Determine the minimum number of cubic inches required for two 10 AWG conductors passing through a…

A: AWG or American Wire Gauge is the US standard measure for the diameter of electrical conductors. The…

Q: Fill in the blanks: Q. Other name of MCR is _______________ Resolution.

A: The Multivariate Curve Resolution (MCR) builds a family of methods that can provide relevant…

Q: What is the meaning of calculated load?

A: Since many different loads are connected to an electrical supply, it is extremely important to know…

Q: 19. When you're connecting a bonding jumper to the structural steel of a building, the jumper must…

A: NEC: NEC stands for National Electric Code. It is a regulatory body that set standard for safety…

Q: In installing a telephone system in a building, PABX is used up to the riser (conduit is used) and…

A: It is mentioned that in installing a telephone system in a building, PABX is used up to the riser…

Q: Answer the following: A) Type of clipper circuit per level of clipping. 1. ___________ 2.…

A: A) Type of clipper circuit on the basis of level of clipping. Positive clipper - this clipper clips…

Q: Briefly discuss the loaded and non-loaded telephone cables

A: Loading is the process to increase inductance of line by adding lumped inductors atpredefined…

Coulomb’s Law

Coulomb's law states that the attraction or repulsion force between two charged things is proportional to the product of their charges and inversely proportional to the square of their distance. It has an effect along the line that connects the two-point charges.