The single-line diagram of a small power system is shown in Fig. 1. The corresponding reactance diagram, with reactances specified in per unit, is shown in Fig. 2. A generator with emf equal to 1.25/0 0° per unit is connected through a transformer to high-voltage node (3), while a motor with internal voltage equal to 0.85/-45° is similarly connected to node (4). Develop the nodal admittance matrix for each of the network branches and then write the nodal admittance equations of the system. T 1 سلت Fig. 1. Single-line diagram ™ 10.25 reelet oooo j0.1 10.25 0000 5/1.15 1.25/0° 0000 0 0.125 0000 10.4 0000 Fig. 2. Reactance Diagram j0.2 j0.1 1.15 0.85/-45

The single-line diagram of a small power system is shown in Fig. 1. The corresponding reactance diagram, with reactances specified in per unit, is shown in Fig. 2. A generator with emf equal to 1.25/0 0° per unit is connected through a transformer to high-voltage node (3), while a motor with internal voltage equal to 0.85/-45° is similarly connected to node (4). Develop the nodal admittance matrix for each of the network branches and then write the nodal admittance equations of the system. T 1 سلت Fig. 1. Single-line diagram ™ 10.25 reelet oooo j0.1 10.25 0000 5/1.15 1.25/0° 0000 0 0.125 0000 10.4 0000 Fig. 2. Reactance Diagram j0.2 j0.1 1.15 0.85/-45

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

How many types of glide resistors? With an explanation of the function of each one
In the Node Voltage Method, a system of equations is written to solve for which of the following? O Component voltages. O Node voltages. O Branch currents. O Currents through voltage sources.
3. Find the equivalent resistance seen between the indicated nodes, in terms of R. The resistors that are in parallel let them be indicated as ()//() without making the complete calculation. a) Between nodes A and B. b) Between nodes F and G. c) Between nodes B AND E. d) Between nodes D AND F.
pls help
Describe series and parallel circuits. Which is used in building electrical systems?
PRELIMINARY EXERCISE Important Note: You are required to do this exercise BEFORE the lab session. a. Explain what is loading effect in measurement. b. Draw the connection using the potentionmeter shown in Figure(i) as a voltage divider. c. The resistance value in Figure (i) are R₁ = 5 k2, R₂-5 k2 and R, -5 k2 respectively. Calculate the error of Moving Coil Meter if it has internal resistance 10 k2 and voltage supply (Vs) is 10V. m Figure (i) d. Discuss the error in voltage measurement between low and high resistance circuit. e. Briefly discuss the difference between a logarithnm and linear track. f. Explain the input and output impedance of buffer circuit. What are the functions of buffer in instrumentation and measurement.
Either all or none .... Vll upvote
When computing complex circuits, why is it advisable to use Kirchhoff’s Rules?
Exercise 2 (from chapter 6) For the diagram below, set up the following items; Kirchhoff loop for the bottom loop of the diagram. Kirchhoff loop for the top loop of the diagram. Kirchhoff loop for junctions A and B.
What is shop drawings, why we use them? I
Write few points about combinational circuits?
Two coils are placed close to each other as shown in the figure. The coil on the left is connected to a battery and a switch, and the coil on the right is connected to a resistor.What is the direction of the current in the resistori. an instant after closing the switch?ii. after the switch has been closed for several seconds?iii. an instant after opening the switch?Choose your answers betweento. on the leftb. on the rightc. the current is zero.And clearly explain the reason for your answer.