The simply supported beam is comprised of a W24x55 wide flange shape with a pin support at "A" and a roller support at "B" (See text Table A3 for W24 properties) 1. Draw shear and moment diagrams for the beam loaded as shown 2. Determine the maximum bending stress in the beam cross section 3. Determine the maximum horizontal shearing stress in the beam cross section P=14 K 6 K/FT В AL А W24x55 10' 3' 5' RA RB

The simply supported beam is comprised of a W24x55 wide flange shape with a pin support at "A" and a roller support at "B" (See text Table A3 for W24 properties) 1. Draw shear and moment diagrams for the beam loaded as shown 2. Determine the maximum bending stress in the beam cross section 3. Determine the maximum horizontal shearing stress in the beam cross section P=14 K 6 K/FT В AL А W24x55 10' 3' 5' RA RB

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine (a) the maximum bending stress, (b) the maximum shearing stress due to V in the simply supported beam shown in the figure and (c) the shearing stress at a point 1m from the right support and 2 cm below the top. 5 cm 40 kN/m 16 kN m A 1-+-2 2 m m CF -2 m 16 cm
Q4: A simply supported I-beam of (2 m) span carries a central load of (4 kN). The load acts through the centroid, the line of action is inclined at (30°) to the vertical direction. Calculate the maximum bending stress at mid-span, and locate the neutral axis. Neglect the weight of the beam. nax Bending 4 KN ➜g N 30⁰ 80 8 mm 160- 25=2 200
Which of the following is the nearest value for the force at member BD? a. 5kN tension b. 1.7 kN tension c. 5 kN compression d. 1.7 kN compression
An over hanging beam ABC of length 10 m (including over hang portion) is shown in the figure below. The ratio of ILD ordinates at C to ILD ordinates at B for the shear force at B is A B 7 m 3 m-
H.W. 1:An axial member consisting of two polymer bars is sup- ported at C, as shown in Figure area ol 540 mm and an elastic modulus of 28 GPa. Bar (2) has a cross-sectional area of 880 mm2 and an elastic modulus of 16.5 GPa. Determine the deflection of point A relative to support C. . Bar (1) has a cross-sectional 50 kN Om She 35 kN (1) (2) 50 kN 0.85 m 1.15 m FIGURE
Compute the maximum tensile and comprsive stresses devloped in the beam that is loaded and has the cross-sectional properties shown in fig 8 KN 120 mm 10 KN/m ΝΑ A 1=20 x10 6 mm4 4m B C 1m 50 mm
Q4: A simply supported I-beam of (2 m) span carries a central load of (4 kN). The load acts through the centroid, the line of action is inclined at (30°) to the vertical direction. Calculate the maximum bending stress at mid-span, and locate the neutral axis. Neglect the weight of the beam. nax Bending 4 KN ➜g N 30⁰ 80 8 mm 160- 25=2 200
stresses in beams 3.
At a point 8ft from D, solve the shear stress 4in from the top of the cross-section. The cross section is 6in by 18in. 16 k 2 k/ft 8k 3 k/ft B -12 ft 8 ft-+9 ft- 12 ft +-9 ft- 4 ft 3 ft 3 ft O 16.46psi O 65.84psi O 8.23psi O 32.92psi
The 80 mm diameter shaft is made of 6061-T6 Aluminum having an allowable shear stress of τallow = 60 MPa. Find the maximum allowable torque T. Also, find the corresponding angle of twist of disk A relative to disk C.