The short-circuit and open-circuit tests were performed on a transformer,with high-voltage rating of 7600 volts and low-voltage rating of 3800 volts.• For the open-circuit test, with the high-voltage side open, the following measurements weretaken from the low-voltage side: 3,800 volts, 0.58 amperes, and 625 watts.• With the low-voltage side short-circuited, the following measurements were taken from thehigh-voltage side: 378 volts, 27 amperes, and 543 watts.For this transformer, what is the core shunt resistance Rc, referred to the high-voltage side?Express your answer in ohms.Answer:

Answered: Image /qna-images/answer/9ee0dd14-3aae-4239-abe0-7826adb5824b.jpg

The short-circuit and open-circuit tests were performed high-voltage rating of 7600 volts and low-voltage rating of 3800 volts. r the open-circuit test, with the high-voltage side open, the following me ken from the low-voltage side: 3,800 volts, 0.58 amperes, and 625 watts th the low-voltage side short-circuited, the following measurements we gh-voltage side: 378 volts, 27 amperes, and 543 watts. his transformer, what is the core shunt resistance Rc, referred to the high ss your answer in ohms. er:

The short-circuit and open-circuit tests were performed high-voltage rating of 7600 volts and low-voltage rating of 3800 volts. r the open-circuit test, with the high-voltage side open, the following me ken from the low-voltage side: 3,800 volts, 0.58 amperes, and 625 watts th the low-voltage side short-circuited, the following measurements we gh-voltage side: 378 volts, 27 amperes, and 543 watts. his transformer, what is the core shunt resistance Rc, referred to the high ss your answer in ohms. er:

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Compute for the Equivalent Resistance of Terminal RBD. Show complete solutions. Strictly use stored values in the computations. Final answers must be written up to fourth decimal place.
Five dry cells having emfs of 2.30, 2.40, 2.35, 2.60, 2.25 Volts and resistances of 0.40, 0.20, 0.35, 0.18, 0.32 Ohm, are connected in series to operate a lamp of resistance 12 Ohms. Determine current and power to lamp.
Explain two method for Measurement of High voltage DC along with neat circuit diagram by hand. Also list the advantage and disadvantages of each method.
A series circuit is set up with an AA battery along with an mystery material and ammeter; however, there’s no current passing through. A.Insulator B.Conductor C.Semiconductor
Refer to Table, showing typical ratings for an LED. Which of the given resistor values would be most suitable for a current limiting resistor, if the LED is to be driven from a Vx=21 V supply? ------ ..-lan dirone doăorlerindon hangici akim cinırlama dire-- --- T Ix Item DC Forward Current IF DC Reverse Current IR DC Forward Voltage VF DC Reverse Voltage VR D1 Vp Power Dissipation Pp Operating Temperature ToPr. Unit mA Value 15 30 (VR = 5V) 2.2 (2.8 Max) HA Vx O 45 -40 to +95 mW °C O a. 1280 2 O b. 1253 2 O c. 1267 N O d. 1240 2 O e. 1293 Q
Three halogen lamps are connected on the same terminal node across 115-volt, 60-Hz source. If each LED lamp is rated 75W, 100W and 150 W, what is the resulting current equation of the circuit?
A 110 volt ac has been rectified by an SCR to power an egg incubator heater. If it is fired at every 80 degree angle, what is the voltage at the heater? if the ac voltage of the first problem has dropped to 95 volts, what should be the new firing angle to maintain the same power at the heater
A cylindrical 00 AWG copper wire is coated with NEMA class B insulation. The normal operating temperature of the wire is 40°C. What is the maximum current the wire can carry for 1 second without exceeding the NEMA temperature rating?
Is the computed average percent error more or less than the tolerance of the resistors? Explain why.
Draw the signal flowchart of the simple resistance network shown below. a) Determine the variables.b) Establish relationships between variables (circuitusing rules).c) Identify branches and nodes and signal flowDraw the timetable.
For the network shown in Figure B22 , assume E = 18V, Diode D¡ as silicon and D2 Germanium, R1=3KQ and R2=2K2. Calculate, i. Current I,, ii. Current In2 ii. Voltage across resistor R2 R1 D E D2 R2 Figure B22 +
(01) AC Diode circuits. (Course: Electronic Devices and Circuit Theory) -Redraw the circuit, Assume diodes are off and Redraw, Apply KVL. -You can add //comments for a better understanding. -Please answer without abbreviation. -Make it clean and clear typing/writing. Thank you.